>>>> Hey Paul,
>>>>
>>>> I heard a rumor that Buly is going to Lycoming.. Is that true??
>>>>
>>>>
>>>> Matt-
>>>>
>>>> Yes. He could not deal with the EFI. I don't blame him.
>>>> For some one not trained in single chip microcomputer hardware
>>>> it is real tough to deal with. The vast majority of people have
>>>
>>> enough
>>>
>>>> trouble with just simple wiring like lights and starters.
>>>>
>>>> You just can't see them electrons :)
>>>>
>>>> Paul Lamar ...No rotor no motor.
>>>>
>>>
>>> I am one of those who found EFI intimidating but I always thought I
>>> would deal with it when the time came. However, there is almost a
>>> continuous thread of problems faced by other builders trying to get
>>> reliable performance out of the the electronic ignition and EFI
>>> which of course I have been reading for years. I can't exaggerate
>>> the relief I felt the when I decided to go to crank fired ignition
>>> and a carb. It was a matter of accepting my own limitations. Jerry
>>>
>>>
>>> Furthermore one is expected to solder 37 tiny wires on this
>>> connector. I would say 80% of the people on here don't have the eye
>>> sight,
>>> skill and manual dexterity required to do this let alone the
>>> electronic knowledge
>>> to trouble shoot such a system.
>>>
>>>
>>> I suggested years ago a simple printed circuit board adapter and screw
>>> type connectors but the idea was rejected out of hand.
>>> --
>>> Paul Lamar ...No rotor no motor.
>>>
>>>
>>> I have 670 hours now and zero problems with [the stock] EFI. Believe
>>> it or not
>>> my
>>> airplane engine has never been flooded. Always starts hot or cold wx,
>>> hot or cold engine.
>>>
>>> Perry
>>>
>>> Well you don't have an RX8 engine either :)
>>>
>>> --
>>> Paul Lamar ...No rotor no motor.
>>
>>
>>
>> Perry,
>>
>> Do you have a turbocharged engine or NA?
>>
>> Doug Fir
>
> It's stock 1986 NA.
> In the early days (1999) I was worried about the EFI not being a
> redundant system, but it's reliability is now proven (it was "proven"
> anyway in car use). Redundancy is only needed for failure prone systems,
> such as magnetos.
> The only redundancy I have is a dual battery system, independently
> selectable but I always run "both". Two sealed r-g lead-acid batteries.
> I've never had a battery failure either, I replaced the originals after
> 5 years, running on the second set now.
>
> Perry
>
> I also might add, Perry is a very talented professional electronic engineer
> so EFI holds no mysteries for him.
>
> Now on the other hand (correct me if I am wrong Perry) he still has
> not got it to lean the engine manually :)
>
> I still think you need to try a pot in the mass airflow sensor circuit Perry.
> --
> Paul Lamar ...No rotor no motor.
>Perry,
>Thanks. Sound like you have a KISS system to me, and it is proven now. What
>is the highest altitude you have flown your bird? I will be going EFI as
>well by choice but then again for various reasons I also don't have a
>choice:) I really don't know what all the phobia is about. With a little
>study anyone can master the basics of modifying the standard auto CPU. For
>safety sake pot the board, and use a back-up if desired.
>If Megasquirt would work with a mass flow sensor than I would consider that
>route. I've given up on using Tracy's unit and it is for sale if anyone
>needs one real cheap.
>Doug Fir
Hi Doug,
Can you describe what you have done and the results you got with
Tracy's unit that have pushed you to the decision to give up on using
it. There are a lot of us that are planning on using it and knowing what
you found as shortcomings would be very helpful. Thanx, DaveM
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.