Subject: Buly is Going Lyco (Too)
From: Rotary Engine
Date: 9/20/2007, 6:48 AM
To: AARotary Engine


Hey Paul,

I heard a rumor that Buly is going to Lycoming.. Is that true??


Matt-

Yes. He could not deal with the EFI. I don't blame him.
For some one not trained in single chip microcomputer hardware
it is real tough to deal with. The vast majority of people have

enough

trouble with just simple wiring like lights and starters.

You just can't see them electrons :)

Paul Lamar ...No rotor no motor.


I am one of those who found EFI intimidating but I always thought I
would deal with it when the time came. However, there is almost a
continuous thread of problems faced by other builders trying to get
reliable performance out of the the electronic ignition and EFI
which of course I have been reading for years. I can't exaggerate
the relief I felt the when I decided to go to crank fired ignition
and a carb. It was a matter of accepting my own limitations. Jerry


Furthermore one is expected to solder 37 tiny wires on this
connector. I would say 80% of the people on here don't have the eye
sight,
skill and manual dexterity required to do this let alone the
electronic knowledge
to trouble shoot such a system.


I suggested years ago a simple printed circuit board adapter and screw
type connectors but the idea was rejected out of hand.
-- 
Paul Lamar ...No rotor no motor.


I have 670 hours now and zero problems with [the stock] EFI. Believe
it or not
my
airplane engine has never been flooded. Always starts hot or cold wx,
hot or cold engine.

Perry

Well you don't have an RX8 engine either :)

-- 
Paul Lamar ...No rotor no motor.



Perry,

Do you have a turbocharged engine or NA?

Doug Fir

It's stock 1986 NA.
In the early days (1999) I was worried about the EFI not being a
redundant system, but it's reliability is now proven (it was "proven"
anyway in car use). Redundancy is only needed for failure prone systems,
such as  magnetos.
The only redundancy I have is a dual battery system, independently
selectable but I always run "both". Two sealed r-g lead-acid batteries.
I've  never had a battery failure either, I replaced the originals after
5 years, running on the second set now.

Perry

I also might add, Perry is a very talented professional electronic
engineer
so EFI holds no mysteries for him.

Now on the other hand (correct me if I am wrong Perry) he still has
not got it to lean the engine manually :)

I still think you need to try a pot in the mass airflow sensor circuit
Perry.
-- 
Paul Lamar ...No rotor no motor.

Perry,


Thanks.  Sound like you have a KISS system to me, and it is proven now.
What
is the highest altitude you have flown your bird?  I will be going EFI as
well by choice but then again for various reasons I also don't have a
choice:)  I really don't know what all the phobia is about. With a little
study anyone can master the basics of modifying the standard auto CPU.  For
safety sake pot the board, and use a back-up if desired.

If Megasquirt would work with a mass flow sensor than I would consider that
route.   I've given up on using Tracy's unit and it is for sale if anyone
needs one real cheap.

Doug Fir


-- Doug

I'm in the process of deciding on a Efi system at the moment for my Glasair
SII Renesis 4 port.
What has been the problem with Tracy's EFI?

Thanks

Steve
Perth Western Australia

Steve,


No problem at all.  As I answered Dave today and  perhaps Paul hasn't posted
it yet, my TEST engine project has gotten more complex then originally
thought.  I have leaped frog testing a side port engine and went directly to
P-port engine with the C/S prop. In short I  realize I need either access to
the  source code or a least a close working relationship to get Tracy's
unit to perform like I need it to.   Neither is likely at my location in
Japan. Case in point 1. injector firing timing and sequencing. 2. use of
alternative fuels, and finally a desire to use a mass airflow sensor and air
temp to calculate fuel charge.

Tracy's unit is fine for what it was designed for.  The unit I bought from
him is still new, unused and in the box if you are interested

Regards


Doug F



Thanks Doug

When did you purchase it?
What engine coils etc is it configured for?
How much do you want for it?

Thanks

Steve
Perth WA

Steve and others. I think it would better to talk off of this forum in
respect for lightening Paul's work load.

Please contact me at fir@ gol.com

Thanks

Doug

No. I am interested too Doug. Fire away.

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.