Subject: Midget Mustang with P-Port 13B
From: Rotary Engine
Date: 9/26/2007, 2:38 PM
To: AARotary Engine



               > Hey Paul,
               >
               > I have seen a number of Midget Mustangs (the single
   seater)
              powered by
               > O-320's.  I just saw an MM powered by an O-360 with a C/S
         prop.  I'd
               > have to think it would be fairly reasonable to stuff a
   13B into
              an MM.
               > Maybe even mount the radiator under/behind the pilot, just
         like the
               > P-51.  Could help the weight and balance.  I've also
   seen a
         couple of
               > MM's with retractable landing gear.  Such a
   combination should
              qualify
               > for Sport Class - enough have been built.  I'd like to
   have a
              structural
               > analysis for flutter.  It shouldn't be against class rules
         to put
              enough
               > more beef in the structure to make it go
   400mph..  Hah.  :)  Or
              at least
               > fast enough to raise some eyebrows.
               >
               >
               > Regards
               >
               > Matt-


              If you want to run in the Sport Class with a Midget
   Mustang, I
         would
              use an
              aluminum 20B.  A better place for the radiators is in the
   inboard
              leading
              edges.  I think this is actually a lower drag
   installation and
         you won't
              have to sit on those coolant lines.

              Steve Brazil


         Rather than an Al 20b, I'd go with a turbocharged aluminum
   13b.  It
         would fit better, and probably fly better, and be plenty of
   horsepower.
         I see a development path on the airframe starting with an
   O-200 (I have
         one), moving to an NA P-Port Iron 13b, and then to
   turbocharged Al (if
         I'm still having fun)..  I realize there's no replacement for
         displacement however.


         Thanks,

         Matt-

         You know Matt there are plenty of cheap Formula 1 airplanes
   for sale.
         Here is the slickest one I have seen so far. Not necessarily
   for sale.

         Paul Lamar



   That's a Mike Arnold designed airplane Paul (the Endeavor - AR-6).  Mr
   Arnold came to fame as a film maker turned airplane designer who built a
   65hp Rotax powered airplane that ran ~215mph on a timed course -
   setting
   a world record, and earning the claim to being the only (or one of few)
   man carrying powered airplanes with a flat plate drag equivalent of less
   than 1 sq ft.  Mr. Arnold studied and applied Hoerner's works
   extensively in the AR-5, and then again in Dave Hoover's Endeavor.  A
   talented guy.

   I suspect that the AR-6 is actually a nice flying airplane, unlike most
   of the F1 birds.  In a conversation I had with Gary Hubler a few years
   ago, I got the impression that Mariah (a heavily modified Cassutt)
   actually didn't fly particularly well - on the first flight he was doing
   aerobatics - a loop required forward stick pressure all the way around.
   They put lead in the prop extension/spinner to try to get the CG more
   reasonable.  Most of the fast f1 airplanes have really thin airfoil
   sections and tiny control surfaces.  Eeesh.

   The MM's are too big to be competitive in F1 racing (IMO), but if you
   put more hp on them they could be pretty fast.  They have conventional
   Aluminum construction which should make structural analysis and
   improvement easier.  The MM is already pretty strong - being rated at
   something around 9g ultimate and having a 230mph published VNE.
   Obviously a study would be required to see what the limitation on VNE is
   and how to increase it.

   I would prefer to keep the overall airframe weight close to the stock MM
   max takeoff weight (at odds with the above goal)..  At that weight the
   MM has a reasonable stall speed (~60mph).  The stall speed has the
   largest effect on bad-landing (off airport) survivability.  It's _much_
   easier to provide impact protection for 60mph than for 90mph.  I am not
   a daredevil nor a fighter pilot, and so I would like whatever I come up
   with to remain a nice sport airplane..  My goal isn't to actually win at
   Reno, but to have something that I could fly to the races, raise a few
   eyebrows, and have well less than $50k in (total).  It would be fun to
   be able to spank a few F1 rockets and slower Lancairs too.


   Regards,

   Matt-

   I totally agree on the stall speed. The energy in a crash is m*V^2.
   Fowler flaps can triple the landing lift coefficient required so if
   you want
   to go fast and keep 60 MPH stall speed you need just enough wing area to
   have
   a stall speed of 60 MPH with the flaps out. The other mandatory
   requirement
   for
   going fast at Reno is a high aspect ratio wing. AKA low span loading
   as you
   are
   in a continuous turn almost. Induced drag is Cl^2/(pi*A). 2G turn
   twice the
   Cl.
   Three G turn 3 times the Cl. Four times as much induced drag at only
   a 2 G
   turn.
   All of this assumes you keep the weight as low as possible.

   I don't think a single place qualifies for Sport Aircraft at Reno.
   That I think is why they put the pax sort of next to the pilot
   in the Nemesis Nxt.

   --
   Paul Lamar ...No rotor no motor.

   Guys,
   Single place is not legal in sport class.... and I inquired about
   rotaries.
   Short answer is they don't want them and will make you run a 13B in
   the 1000
   cubic inch super sport class and I don't think twins are allowed. I will
   have to look it up in the rule book. Do you think they believe it is an
   unfair advantage? To run with the NXT's, will require ~900 hp.
   Larry


   Typical. They are quaking in their boots over a piss ant 160 cubic inch
   engine while they want to run 1000 cubic inches.
   I think they are worried about losing Lycoming and Continental
   sponsorship. Who can we send some nasty email too? Who can we call?
   Can I get that in writing someplace? If they got enough email
   they might change their narrow minds but I doubt it.

   Perhaps the best thing to do is set some city to city records and keep
   entering aircraft in the 500 mile Dayton to OSH race. More pertinent
   anyway
   than 15 minutes around the pylons.

   Paul Lamar ...No rotor no motor.

Larry,

Without intending to be argumentative, I believe I posted the relevant
section of the Sport Class rules (possibly your message and mine crossed
in cyberspace), and can't find anything in them that specifies a minimum
number of seats.

As far as running a rotary, as I said in another message, I don't care
some much about competing with the NXT's.  I just want to show up and go
fast - maybe like Klaus did with his Varieze.  At least, at first anyway.

I agree with Paul that x-country racing is actually a more useful
measure of engine/airplane, but pylon racing is more exciting to watch
(sometimes negatively so).  I think time to climb is interesting too -
in the same way as drag racing.


Regards,

Matt-



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.