Subject: Midget Mustang with P-Port 13B
From: Rotary Engine
Date: 9/26/2007, 8:04 PM
To: AARotary Engine



                     > Hey Paul,
                     >
                     > I have seen a number of Midget Mustangs (the single
         seater)
                    powered by
                     > O-320's.  I just saw an MM powered by an O-360
   with a C/S
               prop.  I'd
                     > have to think it would be fairly reasonable to
   stuff a
         13B into
                    an MM.
                     > Maybe even mount the radiator under/behind the
   pilot,
   just
               like the
                     > P-51.  Could help the weight and balance.  I've also
         seen a
               couple of
                     > MM's with retractable landing gear.  Such a
         combination should
                    qualify
                     > for Sport Class - enough have been built.  I'd
   like to
         have a
                    structural
                     > analysis for flutter.  It shouldn't be against
   class
   rules
               to put
                    enough
                     > more beef in the structure to make it go
         400mph..  Hah.  :)  Or
                    at least
                     > fast enough to raise some eyebrows.
                     >
                     >
                     > Regards
                     >
                     > Matt-


                    If you want to run in the Sport Class with a Midget
         Mustang, I
               would
                    use an
                    aluminum 20B.  A better place for the radiators is
   in the
         inboard
                    leading
                    edges.  I think this is actually a lower drag
         installation and
               you won't
                    have to sit on those coolant lines.

                    Steve Brazil


               Rather than an Al 20b, I'd go with a turbocharged aluminum
         13b.  It
               would fit better, and probably fly better, and be plenty of
         horsepower.
               I see a development path on the airframe starting with an
         O-200 (I have
               one), moving to an NA P-Port Iron 13b, and then to
         turbocharged Al (if
               I'm still having fun)..  I realize there's no
   replacement for
               displacement however.


               Thanks,

               Matt-

               You know Matt there are plenty of cheap Formula 1 airplanes
         for sale.
               Here is the slickest one I have seen so far. Not necessarily
         for sale.

               Paul Lamar



         That's a Mike Arnold designed airplane Paul (the Endeavor -
   AR-6).  Mr
         Arnold came to fame as a film maker turned airplane designer
   who built
   a
         65hp Rotax powered airplane that ran ~215mph on a timed course -
         setting
         a world record, and earning the claim to being the only (or
   one of few)
         man carrying powered airplanes with a flat plate drag
   equivalent of
   less
         than 1 sq ft.  Mr. Arnold studied and applied Hoerner's works
         extensively in the AR-5, and then again in Dave Hoover's
   Endeavor.  A
         talented guy.

         I suspect that the AR-6 is actually a nice flying airplane,
   unlike most
         of the F1 birds.  In a conversation I had with Gary Hubler a
   few years
         ago, I got the impression that Mariah (a heavily modified
   Cassutt)
         actually didn't fly particularly well - on the first flight he was
   doing
         aerobatics - a loop required forward stick pressure all the
   way around.
         They put lead in the prop extension/spinner to try to get the
   CG more
         reasonable.  Most of the fast f1 airplanes have really thin
   airfoil
         sections and tiny control surfaces.  Eeesh.

         The MM's are too big to be competitive in F1 racing (IMO), but
   if you
         put more hp on them they could be pretty fast.  They have
   conventional
         Aluminum construction which should make structural analysis and
         improvement easier.  The MM is already pretty strong - being
   rated at
         something around 9g ultimate and having a 230mph published VNE.
         Obviously a study would be required to see what the limitation
   on VNE
   is
         and how to increase it.

         I would prefer to keep the overall airframe weight close to
   the stock
   MM
         max takeoff weight (at odds with the above goal)..  At that
   weight the
         MM has a reasonable stall speed (~60mph).  The stall speed has the
         largest effect on bad-landing (off airport)
   survivability.  It's _much_
         easier to provide impact protection for 60mph than for
   90mph.  I am not
         a daredevil nor a fighter pilot, and so I would like whatever
   I come up
         with to remain a nice sport airplane..  My goal isn't to
   actually win
   at
         Reno, but to have something that I could fly to the races,
   raise a few
         eyebrows, and have well less than $50k in (total).  It would
   be fun to
         be able to spank a few F1 rockets and slower Lancairs too.


         Regards,

         Matt-

         I totally agree on the stall speed. The energy in a crash is
   m*V^2.
         Fowler flaps can triple the landing lift coefficient required
   so if
         you want
         to go fast and keep 60 MPH stall speed you need just enough
   wing area
   to
         have
         a stall speed of 60 MPH with the flaps out. The other mandatory
         requirement
         for
         going fast at Reno is a high aspect ratio wing. AKA low span
   loading
         as you
         are
         in a continuous turn almost. Induced drag is Cl^2/(pi*A). 2G turn
         twice the
         Cl.
         Three G turn 3 times the Cl. Four times as much induced drag
   at only
         a 2 G
         turn.
         All of this assumes you keep the weight as low as possible.

         I don't think a single place qualifies for Sport Aircraft at Reno.
         That I think is why they put the pax sort of next to the pilot
         in the Nemesis Nxt.

         --
         Paul Lamar ...No rotor no motor.

         Guys,
         Single place is not legal in sport class.... and I inquired about
         rotaries.
         Short answer is they don't want them and will make you run a
   13B in
         the 1000
         cubic inch super sport class and I don't think twins are
   allowed. I
   will
         have to look it up in the rule book. Do you think they believe
   it is an
         unfair advantage? To run with the NXT's, will require ~900 hp.
         Larry


         Typical. They are quaking in their boots over a piss ant 160
   cubic inch
         engine while they want to run 1000 cubic inches.
         I think they are worried about losing Lycoming and Continental
         sponsorship. Who can we send some nasty email too? Who can we
   call?
         Can I get that in writing someplace? If they got enough email
         they might change their narrow minds but I doubt it.

         Perhaps the best thing to do is set some city to city records
   and keep
         entering aircraft in the 500 mile Dayton to OSH race. More
   pertinent
         anyway
         than 15 minutes around the pylons.

         Paul Lamar ...No rotor no motor.

   Larry,

   Without intending to be argumentative, I believe I posted the relevant
   section of the Sport Class rules (possibly your message and mine crossed
   in cyberspace), and can't find anything in them that specifies a minimum
   number of seats.

   As far as running a rotary, as I said in another message, I don't care
   some much about competing with the NXT's.  I just want to show up and go
   fast - maybe like Klaus did with his Varieze.  At least, at first
   anyway.

   I agree with Paul that x-country racing is actually a more useful
   measure of engine/airplane, but pylon racing is more exciting to watch
   (sometimes negatively so).  I think time to climb is interesting too -
   in the same way as drag racing.


   Regards,

   Matt-



   Matt, we just crossed wires... maybe Paul has the wires bent too
   tight....
   And your right... it would be fun just to show up and go fast!
   LArry

   Can we get a full copy of the rules someplace?

   --
   Paul Lamar ...No rotor no motor.


The link is on this page:

http://www.sportclass.com/information.html

And the rules are in this pdf:

http://www.sportclass.com/Sport_Class_rules_2007.pdf


Regards,

Matt-



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.