So Mark I take it the spiral in the exhaust down pipe was not
totally
satisfactory as far as noise is concerned? Is it still in there?
BTW How many hours do you have now? How is your fuel injection
working?
--
Paul Lamar ...No rotor no motor.
Paul,
I would call the spiral flow muffler "marginally adequate". Noise
levels were not exceptionally loud, but after hearing the
Renesis-Hush Power II run, I am envious. Also, the spiral flow
design is showing some signs of flaking and metal fatigue after 1.5
hrs in the air. Until I test the Hush Power II, I plan on welding
up another spiral flow design, but using 321 SS instead. It is
truly amazing how hot the exhaust gas gets. It has melted two AN-3
bolts which were 1/2" inside the exhaust pipe outlet. I
switched to
a stainless steel 1/4-28 bolt and it looks like it can handle the
heat.
As for the ignition, it is doing fine, now that I figured out what was
causing my misfiring condition at high rpm (6500 & up).
On another subject, some of the Lancair ES's have developed cracks in
their motor mounts. I may need to remove my mount and send it back for
magna-fluxing and repair. There have been a number of severe shimmy
incidents, one resulted in nose gear collapse. They're still trying to
figure out why that's happening. I have not experienced any shimmy in
six landings, but they usually begin later on, after 100 or so
landings. Personally, I believe that the mounts are cracking which
weakens the mount and allows the shimmy to occur. The cracks are on the
cross-over tube right at the nose strut attachment. I'll be
inspecting mine for cracks this weekend. Hopefully, I won't have to
ground it for mount/strut repairs.
Other than that, it flies great!
Mark S.
Sorry about messing up the margins. ;-(
From just looking at these pictures of the MM
it does not look like it has any positive damping in rotation other
than the friction in the cylinder seals. Once the seals wear a bit
the friction is probably reduced. A scissor link and a circular
disk damper could be retrofitted. I'll do a 3D for you.
The structural design is not great either. It needs an FEA done
as there are tubes in bending and torsion. I take it you are using the
stock Continental bed mount. I have never been a fan of that mount.
Also some of the bays are not triangulated. CC copied it unfortunately.
I take it you steer with the brakes?
Has Tom Parke's had any nose gear problems. Tom?
Paul Lamar ...No rotor no motor.
Here is the main problem Mark.
None of the horizontal bays have diagonals. Consequently the bending
and torsional strength of the tubes is relied upon to provide this strength.
This leads to high local stress's in the tubes. A true space frame
has no bending or torsional loads in any of the tubes.
I have one of these mounts in my 182. It is a mass of doublers and gussets
applied over the years to all C182's in an attempt to overcome the deficiency of the
original design. In the case of the ES it is worse as now the mount
must deal with the side loads from the nose gear. The C182 has a casting on the
firewall that that takes the nose gear loads.
What it needs is these two red tubes. I am not going to guarantee it will
solve all problems but I am convinced it will help. The other way is keep beefing
up the joints until it stops cracking. That seems to be what most manufactures
that use this mount design are doing. The Bonanza and some Cessna's use an aluminum sheet
metal box under the engine to solve this problem. The Questair venture uses
a mount like most mounts we are using with a Schertz beam.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.