Subject: Lancair nose gear.
From: Rotary Engine
Date: 9/28/2007, 6:59 AM
To: AARotary Engine


        On another subject, some of the Lancair ES's have developed
    cracks in
        their motor mounts. I may need to remove my mount and send it
    back for
        magna-fluxing and repair. There have been a number of severe shimmy
        incidents, one resulted in nose gear collapse. They're still
    trying to
        figure out why that's happening. I have not experienced any
    shimmy in
        six landings, but they usually begin later on, after 100 or so
        landings. Personally, I believe that the mounts are cracking which
        weakens the mount and allows the shimmy to occur. The cracks are
    on the
        cross-over tube right at the nose strut attachment. I'll be
        inspecting mine for cracks this weekend. Hopefully, I won't have to
        ground it for mount/strut repairs.

        Other than that, it flies great!

        Mark S.

        Sorry about messing up the margins. ;-(

         From just looking at these pictures of the MM
        it does not look like it has any positive damping in rotation other
        than the friction in the cylinder seals. Once the seals wear a bit
        the friction is probably reduced. A scissor link and a circular
        disk damper could be retrofitted. I'll do a 3D for you.

        The structural design is not great either. It needs an FEA done
        as there are tubes in bending and torsion. I take it you are
    using the
        stock Continental bed mount. I have never been a fan of that mount.
        Also some of the bays are not triangulated. CC copied it
    unfortunately.

        I take it you steer with the brakes?

        Has Tom Parke's had any nose gear problems. Tom?

        Paul Lamar ...No rotor no motor.





Paul,

I figured some sort of bending/twisting was happening to cause those
cracks.  As for the strut, it does have an internal damping mechanism.
Some of those have blown the o-ring which resulted in severe shimmy, or
maybe it is the other way around (severe shimmy caused it to blow the
o-ring).  There's a mod to those to add a second o-ring.  So far, mine
is doing fine.  I feel that the shimmy is caused by the weakened motor
mount.  The strut mounts in the area where the cracks are forming.

Would you mind if I forward your analysis of the Lancair motor mount to
the Lancair group?  They are headed down the path of adding gussets.  I
don't feel they are addressing the real problem (as you described).

Thanks,
Mark

No problem Mark. Glad to help them out. I would like to shoot the guy that
designed that original mount way back when if he is still alive :)
Unconfirmed rumor has it it was Steve Whitman.

You may not have room for the red diagonals so here is a quick and dirty
band aid. Cut that vertical tube out and replace it with larger diameter thicker
wall as it is obviously in torsion and bending. Replace the front lateral tube with
a larger one and using a 180 degree wrapped finger patch on all the joints in that area.

Add the lateral tube between the front rubber bushings missing in the Lancair ES copy.
Put a small diagonal in the front bay. This is an attempt to transfer some
of the lateral twisting loads to the tubing ring around the bottom of the engine.

The trouble with these bad motor mounts that rely on the torsional and bending strength
of tubing is; you beef up one area and another area then becomes a problem.
Sooner or later they all become a problem with cracks developing. I cringe every
time I see one. Impossible to analyze without FEA. Piston engines are worse than
rotaries  as they vibrate more and stronger.

If somebody wants to do an FEA I can supply them with a dwg in Rhino that can
be imported into Solid Works.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.