Subject: Midget Mustang with P-Port 13B
From: Rotary Engine
Date: 9/28/2007, 4:42 PM
To: AARotary Engine


 I don't know that a Midget Mustang would be legal--not because it is
 single
 place but because I don't think it was ever offered in a kit as
 complete as
 the rules, that someone posted, defined. I wouldn't write off the
 aluminum
 20B; an O-360 with an aluminum constant speed prop weighs around
 350lb and I
 think the aluminum 20B with a turbocharger and a composite prop
 would beat
 that.

 It is also true that the Midget Mustang is a tough little
 airplane. What
 you have to worry about, taking it a lot faster than it was intended,
 is
 flutter and the increased dynamic pressure. I think you will need
 additional spanwise stiffeners on the forward wings and tail
 surfaces, maybe
 a thicker windscreen, stronger landing gear fairings and a stronger
 cowl.
 There are people who can help analyze and prevent flutter. You may
 also
 need taller gear for the larger prop.

 This could be interesting. The reason that that Zivko Edge went so
 fast is
 that it had a GEARED O-540. They're going fast enough now that
 propellers
 are getting critical and 2.85 to 1 reduction is available for
 rotaries.

 Steve Brazil

 Steve,

 I agree with all of your analysis except for whether I want the weight
 of an O-360 and a CS prop on the front of a MM. I kind of think I don't
 want that. I'd like to shoot for O-320 weight or less in order to
 retain bad-landing survivability, and to have good span loading and low
 trim drag. Obviously if your sense of the numbers is better than mine,
 a 20b as you described would be the way to go.

 Regards,

 Matt-

 There isn't much difference in weight between the O-320 and O-360.
 It can
 be as little as ten pounds depending on variant. The big problem
 with that
 airplane is the propeller. The drawing calls out a 56 inch diameter
 prop.

 http://www.mustangaero.com/images/Midget%20Mustang/Midget%203%20View.JPG

<http://www.mustangaero.com/images/Midget%20Mustang/Midget%203%20View.JPG>

 I think you will need a four-blade prop about 72 inches in diameter
 which
 will mean the gear will need to be another probably six inches
 taller. MT
 is probably the only supplier around for a composite prop like that,
 the
 weight of a metal one, if there was one available, would be prohibitive.
 Another six inches in the aft fuselage would help along with a little
 taller
 vertical and it would still only be about 17 feet long. I think this
 would
 work but you will have to be very careful getting used to flying it.
 I was
 talking to my buddy today who I had helped race his RV at Reno a few
 years
 ago and he thinks this has possibilities too. Talking about RV's it
 isn't
 the aspect ratio of the Rockets as much as it is the NACA 23014 airfoil.
 The Midget Mustang has a much faster, thinner laminar airfoil.

 I still think the airplane to look at is the short wing Glasair II
 RG. It's
 a nose dragger, which I don't care for, but it's easier to deal with
 on the
 ground. It has enough room in the cowl for a turbocharged, aluminum
 20B and
 it was designed from scratch to use an engine of this weight. It has
 room
 for a 72 inch propeller and you should have no problem with the rules.
 There are also abandoned kits around that can be had for reasonable
 money.
 One of these things with 500hp and a prop running at 2500rpm would
 be in
 the
 running. A FIXED GEAR Glasair II TD ran at better than 265 at Reno last
 year with probably 240hp from his four-cylinder Lycoming (I don't know
 if it
 had 390 or 400 cubic inches).

 Steve Brazil

 Steve,
 That airplane is supported by the factory. It started life as a 390,
 don't know the current displacement! I can say that it has a hell of a
 lot more than 240 HP! 300+ as a mimimum.
 FWIW.
 Bill Jepson


I appreciate the thoughts.. My idea was to pick the smallest proven
airframe that could accommodate a 13b and still be a nice flying
airplane. The 13b is great because it's possible to keep costs down by
using off the shelf parts, and because it's just simpler - fewer total
parts. Like I said in previous messages, I am interested in have a nice
sport plane, not some flying "manhole cover," so I think a 20b is a
non-starter. I am not trying to discourage others from pursuing their
own dreams, however.

I had also concluded that a Midget Mustang with a 13b would need longer
gear for prop clearance. Before I gave up on the idea of running at
Reno, my buddy and I were speculating on the Sport Class rules and
whether the description of the kit to include landing gear meant that
the airplane actually had to use the landing gear from the kit, or
whether substitutions could be made. If it were required to use the
original gear, certainly extensions could be devised. My other idea was
to use (pieces of) the existing gear as a portion of the lower section
of a retractable system akin to the Grumman Bearcat - the upper portion
of which swings out, the lower portion swings in, kind of folding on
itself.

http://www.warmkessel.com/jr/flying/td/jd/images/pp39_main_gear.jpg

How to put retractable gear on a little airplane with a big engine...

Regards,

Matt-

Matt,
The rules are pretty liberal on modifications. Daryl Greenameyer's plane
had large portions of the fuselage reshaped. Also the wing was completly
re-done. This may be one of these "old boy" deals. Before trying it
yourself you would be best off to check with the officials and get it in
writing that a mod was OK!
Bill Jepson


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.