Subject: One rotor Rotamax at Copper State - some information of charge cooling
From: Rotary Engine
Date: 11/23/2007, 5:51 PM
To: AARotary Engine



    > > Perhaps what is also happening is silicon nitride ceramic roller
    > > rotor bearings and
    > > silicon nitride ceramic apex seals are being used so it is less
    > > important to cool
    > > the rotors. Ceramic roller bearings are less affected by high heat
    > > than steel
    > > bearings. Same goes for apex seals. Some of the reasons for oil
    > > cooling the rotors
    > > in the Mazda is to cool the rotor bearings and help cool the apex
    > > seals. Most of
    > > the apex seal cooling is now done by the injected apex seal oil in
    > > the Mazda engine.
    > >
    > > With less rotor cooling there is less waste cooling heat.
    > >
    > > Paul Lamar ...No rotor no motor.
    > >
    > > Paul,
    > > Since the Mazda uses plain bearings anyway it would seem oil
   cooling
    > > would be more of a natural solution. The first company that ever
   did the
    > > pass-thru charge cooling, (to my knowledge anyway), was BSA.
   They had a
    > > full road going prototype motorcycle shortly before going
   bankrupt.
   Some
    > > people say that was the basis for the Norton rotary, others tell me
   that
    > > it was an independent effort. Mazda was impressed enough with
   the BSA
    > > effort to buy several of the new patents they filed. I often
   wondered if
    > > a blended variant might work well. The idea would be to use air
   cooling
    > > for the rotor, with the standard water for the housings. The rotors
    > > could be considerably lighter that way. Just thinking out loud.
    > > Bill Jepson
    > >
    > > The Norton and Midwest, now Diamond, engines use air cooling.
    > > It is not free however as it take HP to drive the required
    > > air pump.
    > >
    > > Paul Lamar ...No rotor no motor.

   I agree with you, Paul, that air-cooling is not "free" as it does take
   horsepower to drive the required air pump.  Nevertheless, what if we
   took another look at cooling the Wankel engine with air directly?

   Porsche has had some experience with air-cooled engines in automobiles.
   In fact, the 5-liter 917 flat-12 engine was air-cooled (a photograph of
   which can be found here:
   http://www.pelicanparts.com/vasekauction/917-3/med/DSC02088.JPG).

   Paul Frere, in his article on the Porsche 917 in "Cars in Profile,
   Collection 1" (Profile Publications Limited, 1973, Doubleday & Company,
   1974), noted:

   "Another shaft drives  . . . the cooling blower running at 0.895 engine
   speed . . . (p. 98)

   (A photo of the blower can be found here:
   http://www.pelicanparts.com/vasekauction/917-2/med/DSC01966.JPG)

   "(in 1969) . . . the engine had been developed to give some 580 hp, and
   those who think an air-cooled racing engine loses too much power in
   driving its cooling blower will be interested to know that this absorbed
   only 17 bhp at peak revs (/and at 236 mph - LN/). . . .  This is, of
   course, much less than the power required to drive a large water
   radiator
   through the atmosphere at over 200 mph. (p. 104)"

   On the basis of Porsche's automotive experience, could not an
   aircraft-based Wankel engine be cooled more efficiently with air than
   with a water-to-air radiator?  Especially if the air cooling system uses
   heat pipes?

   Les Nordman :-)

   Page 104 of which book?

   Porsche built a fan cooled aircraft engine for the Mooney and it
   burned more fuel
   than a Lycoming. You still have to get the cooling air into the
   cowling and out so the
   drag due to that is not zero.

   http://www.mooneyland.com/Mooney%20Models.htm
   <http://www.mooneyland.com/Mooney%20Models.htm>

   Robinson derates the Lycomings because of the cooling fans.

   It is near impossible to air cool a two rotor without separating the
   rotor housings with more distance. That adds to the stress on the
   e-shaft
   and to the weight of the engine.

   I am not saying it is impossible. Just not practical.

   Paul Lamar ...No rotor no motor.


I thought Robinson derates the chopper engines to promote
longevity/reliability...


Regards,

Matt-

They cannot deliver the rated HP to the gear box because they need
to drive the fans. Some rogue engineer is likely to run the numbers
and find the missing 10 HP in the climb rate :)
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.