Subject: Needle valve slide carbs. Was P-port
From: Rotary Engine
Date: 11/26/2007, 4:29 PM
To: AARotary Engine


I don't know why I did not think of this a couple of years ago.
I just was not thinking fixed needle movable fuel jet.
This is by a factor of ten simpler and easier to build than anything I
have come up with
so far. It uses a low pressure pump and a low pressure pressure
regulator.
Your done!!!! Assuming you have a slide throttle. Adjust the regulator to
lean.
Turn the pump on after the engine is turning over to start.
To prime turn the pump on for a second or two and then off.

Paul Lamar ...No rotor no motor.

Paul,
This seems to be a fixed needle, (with integral needle and jet) x 2.

Wouldn't the fuel therefore need to be fed to the other, thicker end of
the
needle.The biggest draw-back of a fixed needle is getting the fuel to the
jet, as the jet would be in most cases moving with the slide.

You have designed around this problem but I do see a couple of things to
consider, like the thickness of the needle- rod , but that is just a
relative thing ( i.e. fuel flow to air flow). I would personally go for
the
flat ground needle to maintain more width thickness of the needle,
therefore
keeping the needle diameter down to the smallest size.

One of the claimed draw-backs of the round ground needle is that it tends
to
rub against the jet wall in one area and causes uneven wear of the jet,
that
leads to an uneven flow distribution. However where it's one piece like
this, there isn't that sort of problem.

I may be wrong but I thought that round ground needles needed the
increased
signal of a venturi to better draw the fuel. That's why I like the flat
ground needle as it creates it's own low pressure area behind the needle,
which draws the fuel up through the jet. Then again you mentioned the low
pressure pump and Regulator to initiate and maintain correct fuel flow. I
will use the same system but just enough pressure to get the fuel to
within
striking distance, to respond to the low pressure area created by the flat
ground needle.

If I am seen to be pushing the flat ground needle, it's just because I
would
like both yourself and Doug to fully understand the benefits, before you
eliminated it as a contended for a design.

One other thing to consider is fuel cut-off, but I suppose you will just
cut-off the fuel pump?

George (down under)


Here is the needle design and a chart showing fuel jet port area as a
function
of the smaller diameter of the needle. The OD of the needle is .2 inches.

Looks like the small diameter should be about .16" for a fuel flow
of 22 gallons an hour high power at 2 psi fuel pressure.

This is going to be one super cheap FI system using only off the shelf low
pressure fuel pumps and  an adjustable low pressure regulator.

Dave, hang on to my RX8 p-port engine. I am making one of these and we
will be trying it again on the dyno soon. Stand off mist should
not be a problem as the fuel is injected down near the engine
16 inches away from the runner bell mouths and about 3 inches
in from the p-port itself. In other words inside the sealed slide
throttle.
-- 
Paul Lamar ...No rotor no motor.

Paul,
Most adjustable low pressure fuel regulators go to 6 psi, so if your set-up
shows your running too lean you can adjust your regulator. I see the
regulator as the course adjustment and would suggest a fine adjustment of
the needle, simply by having a thread and nut to adjust the needle up and
down (back and forth).

Of course most needles aren't just one linear line form fully open to fully
closed, they are stepped and change from idle to cruise to wot. Exactly
where and by how much is a matter for experimentation. This is where an O2
sensor comes in handy, as it will identify where the needle is too thick or
too thin.
George ( down under)

That is a REAL good idea George. Really easy to implement on this design
as the needle sticks out the front end of the slide. Thanks for thinking of
that. It could be motorized even with a big gear and a small pinion turned
by a DC motor.

I don't think you need the stepped needle because in an aircraft engine
you adjust the leaning at steady RPM cruise. You take off at WOT. It is not
like a car or a motor cycle where the RPM and load vary over a wide range.
All you need is to keep the engine running and the rotary will run from about
10:1 to 18:1 mixture.

-- 
Paul Lamar ...No rotor no motor.

Paul,
You may well be right about the needle taper, I hope you are, it would sure
make things easier.

On the threaded adjustment of the needle, this could be manually done, as it
is currently done - from the cockpit / turn knob, for rich and lean, with
the cable going from cockpit ( knob) to the needle/jet threaded rod.

This is how I plan my rich/ lean adjustment also.

The next thing I would reconsider is moving away from the electric pump and
going back to the manual pump you designed a little while back OR have both
for redundancy. Certainly use the electric pump for testing.

The carb discussion has been very stimulating, I wish Doug had tossed in his
2 cents worth. It's always interesting to see others opinions and if I have
contributed in any way - it's my pleaser to do so. Acceptance of an idea
reinforces that I am heading in the right direction also.

George (down under)


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.