Subject: Needle valve slide carbs. Was P-port
From: Rotary Engine
Date: 11/27/2007, 9:39 AM
To: AARotary Engine




    > Easy. The engine will gulp fuel at full or over rich.
    > Here is a chart showing GPH on the dyno with a Weber carb that is not
    > necessarily tuned properly for a tuned manifold.
    > Paul Lamar

   Paul,
   That chart seems to be all over the shop, the only thing that has an
   incremental climb is the EGT. Why the big BSFC jump at 6,000 rpm,
   then slump
   at 6600 and 6700 rpm etc.
   George (down under)


   That is to be expected with any type of venturi fuel feed and a resonant
   intake system. A p-port rotary engine with a 20 inch long two
   inch diameter tuned pipe is a very very powerful resonant
   system. Think how load a pipe organ is. Now think how load
   that pipe organ would be with a 200 HP pump driving the pipes.

   There are no intake valves to get in the way. It is basically a long
   cylinder with
   a piston moving back and fourth in one end at up to 7500 times a
   minute.
   It is not for nothing a p-port rotary can fill it's displacement chamber
   with 120% of atmospheric air pressure.

   A variable amount of air and pressure is flowing back and fourth
   at the speed of sounds over that venturi sucking fuel out at different
   rates depending on the RPM and the exact point in the resonant spectrum
   the engine happens to be in at the time.

   The mixture becomes all over the map. It must be adjusted by a
   computer or
   manually in our case by the pilot. Fortunately for aircraft use the
   engine
   runs at one RPM and we can adjust the mixture to suite. In the air at
   cruising speed one has to deal with the dynamic pressure coming into
   the air box so that becomes another variable depending on the speed
   of the airplane. Again the mixture must be adjusted accordingly.

   BTW all you people doing FADECS. Mistral and Rotamax. This is
   something you are going to need to deal with as you install your
   engines in different types of aircraft. If you use a mass airflow
   sensor and a computer you will have to damp the mass airflow signal
   to average
   the airflow out as it too will respond much like a venturi to this
   back and fourth airflow. Same thing goes for a MAP sensor.

   A better idea is to measure the actual pressure in the intake chamber
   area right after the port closes with a high speed pressure sensor and
   forget about the mass airflow sensor. That is the bottom line. I have
   mentioned this before. Tracy should and could do it using the Mazda
   apex seal oil injection port. See the attached picture. Perhaps a better
   place to do it is at the very top of the engine which will require
   drilling through a rib in the Mazda cooling system. See the second
   picture
   with the red line.

   The dyno runs over a wide RPM range at full load quickly so it is not
   possible to manually adjust the mixture. Next time we do a dyno run
   I will
   try running it at a constant 5000 RPM with a constant load and see
   if I can
   adjust the mixture to the best fuel burn. We will probably have to
   sneak
   up on it. 3500, 4000, 4500 and finally 5000 RPM.

   Paul Lamar ...No rotor no motor.

The thermal mass flow sensors (heated grids/vanes) probably don't have
any problems with the resonant effects.  The time constant associated
with changing the temperature of the sensor is likely accomplishing the
damping effect you mentioned..


Regards,

Matt-

I am not so sure when the engine is running at a constant RPM. The air is
flowing back and fourth over the hot wire 6500 times a minute cooling the
wire more indicating more air is flowing  into the engine than is really
happening. I agree the hot wire probably does not see the individual pulses.
I could be wrong.

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.