>> I don't know why I did not think of this a couple of years ago.
>> I just was not thinking fixed needle movable fuel jet.
>> This is by a factor of ten simpler and easier to build than anything
I >> have come up with
>> so far. It uses a low pressure pump and a low pressure pressure >>
regulator.
>> Your done!!!! Assuming you have a slide throttle. Adjust the
regulator to >> lean.
>> Turn the pump on after the engine is turning over to start.
>> To prime turn the pump on for a second or two and then off.
>>
>> Paul Lamar ...No rotor no motor.
>
> Paul,
> This seems to be a fixed needle, (with integral needle and jet) x 2.
>
> Wouldn't the fuel therefore need to be fed to the other, thicker end
of > the
> needle.The biggest draw-back of a fixed needle is getting the fuel to
the
> jet, as the jet would be in most cases moving with the slide.
>
> You have designed around this problem but I do see a couple of things to
> consider, like the thickness of the needle- rod , but that is just a
> relative thing ( i.e. fuel flow to air flow). I would personally go
for > the
> flat ground needle to maintain more width thickness of the needle, >
therefore
> keeping the needle diameter down to the smallest size.
>
> One of the claimed draw-backs of the round ground needle is that it
tends > to
> rub against the jet wall in one area and causes uneven wear of the
jet, > that
> leads to an uneven flow distribution. However where it's one piece like
> this, there isn't that sort of problem.
>
> I may be wrong but I thought that round ground needles needed the >
increased
> signal of a venturi to better draw the fuel. That's why I like the flat
> ground needle as it creates it's own low pressure area behind the
needle,
> which draws the fuel up through the jet. Then again you mentioned the
low
> pressure pump and Regulator to initiate and maintain correct fuel
flow. I
> will use the same system but just enough pressure to get the fuel to
> within
> striking distance, to respond to the low pressure area created by the
flat
> ground needle.
>
> If I am seen to be pushing the flat ground needle, it's just because
I > would
> like both yourself and Doug to fully understand the benefits, before you
> eliminated it as a contended for a design.
>
> One other thing to consider is fuel cut-off, but I suppose you will just
> cut-off the fuel pump?
>
> George (down under)
>
>
> Here is the needle design and a chart showing fuel jet port area as a
> function
> of the smaller diameter of the needle. The OD of the needle is .2
inches.
>
> Looks like the small diameter should be about .16" for a fuel flow
> of 22 gallons an hour high power at 2 psi fuel pressure.
>
> This is going to be one super cheap FI system using only off the
shelf low
> pressure fuel pumps and an adjustable low pressure regulator.
>
> Dave, hang on to my RX8 p-port engine. I am making one of these and we
> will be trying it again on the dyno soon. Stand off mist should
> not be a problem as the fuel is injected down near the engine
> 16 inches away from the runner bell mouths and about 3 inches
> in from the p-port itself. In other words inside the sealed slide >
throttle.
> -- > Paul Lamar ...No rotor no motor.
Paul,
If your referring to the graph in the previous e-mail ( 2 psi) and your
estimating approx ( I use my own figures) 10.5 gph x 6 lbs per gallon = 63
lb/hr ( per rotor) would indicate .063 "( dia). In my flat needle .0625" (
1/16") is half of my ground needle of 1/8 "( .125").
Most of the needles I've seen are no more than 1/8" before taper and I have
copied that. Being one piece your needle my be thicker. In this
application,
I would reconsider the hollow needle with the small holes at the back like
the Ellison. The low pressure are behind the needle is the same
principle as
in the flat needle.
George (down under)
Opss you are right! I need more like 100 pounds per hour or 16.7 gallons
an hour
per rotor. Looks like the small diameter will be .1 inch or less. I was
mistakenly
reading the chart as gallons per hour. Of course I can always jack up
the pressure
a bit to squirt more fuel with small diameter of .1 inch.
There is no reason a .2 inch needle instead of .125 inch diameter cannot
be used.
What counts is the opening AREA of the jet. The small diameter is what
counts.
I need the larger diameter for structural reasons as the needles are
connected
end to end.
I am figuring full rich 12.5:1 WOT.
Paul Lamar ...No rotor no motor.
The other thing to remember Paul is that the larger needle will require
a shallower taper. With the starting diameter larger the annular outlet
will increase quickly with opening. Rather obvious as the radius/area is
a squared function, but easy to overlook when running with a brainwave
like this.
Bill Jepson
I don't think so Bill.
I used QB to calculate the opening area as a function of the small diameter.
That is the port area chart.
It appears to be a linear function of the small diameter.
Here is a rough hand plot of opening area verses small diameter.
BTW QB is a powerful and quick programming language for engineering
purposes. If anybody wants it let me know. I can email it as a zip file.
It runs well in the command line of Windows XP. There are a few tricks to using
it effectively so if anybody wants to use it I can help.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.