Subject: Needle valve slide carbs. Was P-port
From: Rotary Engine
Date: 11/27/2007, 11:08 AM
To: AARotary Engine



     > Easy. The engine will gulp fuel at full or over rich.
     > Here is a chart showing GPH on the dyno with a Weber carb that is
not
     > necessarily tuned properly for a tuned manifold.
     > Paul Lamar

    Paul,
    That chart seems to be all over the shop, the only thing that has an
    incremental climb is the EGT. Why the big BSFC jump at 6,000 rpm,
    then slump
    at 6600 and 6700 rpm etc.
    George (down under)


    That is to be expected with any type of venturi fuel feed and a
resonant
    intake system. A p-port rotary engine with a 20 inch long two
    inch diameter tuned pipe is a very very powerful resonant
    system. Think how load a pipe organ is. Now think how load
    that pipe organ would be with a 200 HP pump driving the pipes.

    There are no intake valves to get in the way. It is basically a long
    cylinder with
    a piston moving back and fourth in one end at up to 7500 times a
    minute.
    It is not for nothing a p-port rotary can fill it's displacement
chamber
    with 120% of atmospheric air pressure.

    A variable amount of air and pressure is flowing back and fourth
    at the speed of sounds over that venturi sucking fuel out at different
    rates depending on the RPM and the exact point in the resonant spectrum
    the engine happens to be in at the time.

    The mixture becomes all over the map. It must be adjusted by a
    computer or
    manually in our case by the pilot. Fortunately for aircraft use the
    engine
    runs at one RPM and we can adjust the mixture to suite. In the air at
    cruising speed one has to deal with the dynamic pressure coming into
    the air box so that becomes another variable depending on the speed
    of the airplane. Again the mixture must be adjusted accordingly.

    BTW all you people doing FADECS. Mistral and Rotamax. This is
    something you are going to need to deal with as you install your
    engines in different types of aircraft. If you use a mass airflow
    sensor and a computer you will have to damp the mass airflow signal
    to average
    the airflow out as it too will respond much like a venturi to this
    back and fourth airflow. Same thing goes for a MAP sensor.

    A better idea is to measure the actual pressure in the intake chamber
    area right after the port closes with a high speed pressure sensor and
    forget about the mass airflow sensor. That is the bottom line. I have
    mentioned this before. Tracy should and could do it using the Mazda
    apex seal oil injection port. See the attached picture. Perhaps a
better
    place to do it is at the very top of the engine which will require
    drilling through a rib in the Mazda cooling system. See the second
    picture
    with the red line.

    The dyno runs over a wide RPM range at full load quickly so it is not
    possible to manually adjust the mixture. Next time we do a dyno run
    I will
    try running it at a constant 5000 RPM with a constant load and see
    if I can
    adjust the mixture to the best fuel burn. We will probably have to
    sneak
    up on it. 3500, 4000, 4500 and finally 5000 RPM.

    Paul Lamar ...No rotor no motor.

The thermal mass flow sensors (heated grids/vanes) probably don't have
any problems with the resonant effects.  The time constant associated
with changing the temperature of the sensor is likely accomplishing the
damping effect you mentioned..


Regards,

Matt-

I am not so sure when the engine is running at a constant RPM. The air is
flowing back and fourth over the hot wire 6500 times a minute cooling the
wire more indicating more air is flowing  into the engine than is really
happening. I agree the hot wire probably does not see the individual pulses.
I could be wrong.

Paul Lamar

Paul,
The trick to a mass air flow sensor is to mount it forward of the air plenum
that is feeding the 2 inlet runners. The plenum gets sized to become the
damper for the pulsing. The inlet tube to the plenum can also be long with
the mass sensor mounted on the end of the inlet tube with an air filter
mounted directly on the mass air.
Larry

That sounds like that will work great Larry. Thanks.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.