Subject: Low pressure mechanical fuel injection progress.
From: Rotary Engine
Date: 12/11/2007, 3:51 PM
To: AARotary Engine


Paul,
Looking good, however I can't understand why you need a number of needles
when only one would do if you adjust it with a threaded end - especially
since your taper is totally linear. It seems an overly complex way of doing
it to me.

I have my needle seated on a spring  and a threaded rod that pushes on the
needle guide. The spring keeps the needle and guide positively positioned
against the threaded rod - which also acts as the throttle.

Turning the rod pushes the needle and guide up and down, leaning and
enrichening - pushing and pulling on the rod is the throttle control. With
one knob you can throttle and lean, at the same time if you want to.

Attached is a photo of the needle in guide (slide carb 13). The spring
slides over the needle and sits under the guide, the needle and guide slide
into the slide plate (slide carb 18). Again in 19. There is a top plate with
a threaded centre hole which the throttle rod screws into and pushes on the
needle and guide.

Can't get much simpler than this!

George (down under)

We do both. Changing the needle taper alone changes the rate of fuel flow
as a function of throttle opening. Flow at idle stays the same.
If you screw the needle in and out it moves the curve left and right.

However we also change the pressure which increases or reduces the
flow over the entire throttle movement range. About the same thing
as moving the needle in and out. This is easier to do as we need a fuel
pressure regulator anyway. One might as well use an adjustable regulator
as they don't cost any more than a fixed pressure regulator. They
can easily be mounted on the instrument panel. No additional
mechanical linkage required to move the needle in and out.

The other thing about the needle taper is it does not have to be linear.
Suppose the engine is too rich in the middle of the range and too
lean at the top end. Changing the taper along the length of the
needle fixes that. The last Posa graphic illustrates that option.

Paul Lamar

Paul,
I agree totally with what your saying, however I see the adjustable
regulator as a coarse adjustment for set-up purposes and the needle as the
fine adjustment. Mainly because of the ability for cockpit needle adjustment
would IMO be the easiest adjustment to make.

I would be happy to be proven wrong in this regard and the work your doing
will help me immensely, so I'm not trying to be critical, just thought  my
ideas may save you some time and money, as it would be so much easier on
your round needle set-up. On the round needle there isn't a concern of the
needle turning as there is with my set-up.

I actually moved away for the round needle design for two reasons, one was
that the round needle lost pick-up signal as the size diminishes - as the
taper reduces.This in itself may vary regulator adjustment. This is not a
problem with a flat back taper as the front of the needle is the same width
at the face ( incoming air side) of the needle.

The other reason is that a pointy ended taper causes the needle and seat to
wear unevenly  as the needle is often pushed to one side. You have designed
around the second problem as the needle is endless - I must say I hadn't
thought of that particular solution.

I think you will find that the needle may require some tuning or adjustment
beyond linier, but at the rate your going you should be able to ID this in
short order.

I was pleased to see the 20 B You-Tube video with the slide throttle and how
well it worked. I shot off a request for some info on it, I don't know if
you did the same? What I also found interesting was the very small amount of
opening of the square slide for idle- even when he gave it a hit (throttle)
the slide didn't move very much at all.

Even though or designs are different they have the same design goals and
there is usually more than one way to meet these goals. So I am very excited
to hear about your results.

George (down under)


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.