Subject: Preliminary Lancair 360 turbo plumbing 3D
From: Rotary Engine
Date: 12/18/2007, 7:34 AM
To: AARotary Engine



       Hi Jerry,


       No I'm not getting these from Paul.  I have to say I like the
       way this is shaping up.  I have not had very much luck with
       Mistral.  I tried and tried to get them to sell me a back plate
       so I could use my dyna focal mount.  When I finally got ahold of
       them they said they had changed the design and couldn't help me.
        I know they are very busy with their certifications.  I wonder
       if their turbo would work anyway because their rotary is based
       on a 13B which I believe is ported differently.  If you think we
       can make it work, I'll ask about it.  I have heard they are
       mighty pricey though.


       Nevertheless, I have to say that this seems a very elegant way
       to get me a turbo and not string intake across the top where I
       clearly have no extra room.  Carlos Gonzalez will help me with
       the intake and exhaust and he is also a turbo dealer.  I'll send
       these to him to see what he thinks. Where do you suppose the
       exhaust will go from where it ends now?  Down the side of the
       cowl and then down? I still need a radiator and oil cooler too.
        Do I need a turbo intercooler or am I looking at it?

       We are looking good though, press on!


       Thanks,


       Steve


           Steve,  I don't know if  you are receiving this stuff from
           Paul or not.   If you are let me know an I stop forwarding
            it to you.  The Mistral turbo is perfect.  You can see your
           engine mount taking shape in the  3Ds.      Jerry


           Begin forwarded message:


               *From: *Rotary Engine <rotaryeng@earthlink.net
               <mailto:rotaryeng@earthlink.net
               <ailto:rotaryeng@earthlink.net">>>

               *Date: *December 17, 2007 2:07:10 PM GMT-05:00


               *Subject: **Preliminary Lancair 360 turbo plumbing 3D*


               This is the stock 2nd gen turbo and exhaust manifold.

               Beg, borrow, steal or mortgage the family home

               and get a Mistral turbo designed specifically for

               the rotary. Doug Fir noticed it was turned around

               the right way for tractor aircraft use. The turbine is at

               the back and the compressor is at the front where it needs

               to be. No crossing over the exhaust and intake plumbing

               as shown here in the 3D's. Thank you Francois.


               Here is a picture. Also a picture of Dave Leonards stock

               2nd gen turbo install which I stole.

               --

               Paul Lamar ...No rotor no motor.


   Steve,  are you a member of Paul's rotary news letter?  If not, join up.
   Lots of excellent info.  So far the conversation has just been between
   Paul and me.  I think by tomorrow or Wednesday he will have a drawing
   that includes the rads.  Once the drawings are completed he will publish
   them in the newsletter.

   In the drawing you are looking at the inter cooler in front of the
   turbo.
   You must have the inter cooler I am sure.  I am not an expert in turbos
   or intakes, but I think you  could buy just  the Mistral turbo and build
   an exhaust flange to fit it to  your engine.   Generally speaking, the
   turbo does not need a muffler as it quiets the exhaust sufficiently by
   itself.  You can snake an exhaust pipe out the bottom. I would get it
   out of the cowl as quickly as possible.

   To join the newsletter go to: rotaryeng@earthlink.net
   <ailto:rotaryeng@earthlink.net">
   <mailto:rotaryeng@earthlink.net <ailto:rotaryeng@earthlink.net">>

   Jerry.

   I might add the exhaust flange is part of the Mistral turbine housing.
   Brilliant. I have not heard from Francois lately as he has been very
   busy supplying helicopter engines to the Russians. I do hope he
   will sell this turbo separately without support of any kind. He is not
   set up to sell parts as it is not cost effective for him. Too much
   support has been required in the past. People have abused Mistral's tech
   support in the past. That has ruined it for the rest of us.

   I take it from your comments above Steve you are planning on adding
   a turbo
   to the RX8 engine. Be cautious as the compression ratio is higher
   in the RX8 engine and there are no low compression rotors available
   yet. I think the best that can be expected from a turbo RX8 engine
   right now is flat rating. In other words no boost at sea level and
   just enough
   boost at high altitude to keep the engine at sea level power.
   If you don't already have an RX8 engine your best bet for a turbo
   rotary is a 3rd gen turbo RX7 engine. This engine was developed and
   finally
   generated 280 HP stock. The Mistral and 1991 2nd gen stock turbo
   will fit.
   The second gen stock turbo must be modified to slow it down or it
   will not live.

   I also suggest getting a copy of Hugh MacInnes classic book
   "Turbochargers."
   Used on the Internet for as little as $9.

   There is another approach to high HP at altitude and that is build in so
   much power at sea level you have more power at high altitude than
   most people
   with normally aspirated engines. Mark Suspinski is taking this approach.
   Our P-port RX8 engine has developed 264 HP at 7500 RPM at sea level
   so far.
   At 7500 feet density altitude it would still be about 210 HP. You lose
   the weight of the turbo but you make it up with the required muffler as
   Jerry pointed out above. This is about what you would get out of a flat
   rated RX8 turbo engine at 7500 RPM.

   A drawback to this approach for the
   Lancair 320-360 is the 19 inch long straight intake runners required.
   No room on top of the engine. This means you will need an Me109 or
   P38 style
   ram air box on the left side of the cowl similar to Dave Leonard's
   RV6 turbo.

   Paul Lamar ...No rotor no motor.

Steve,  read Paul's comments regarding turbo vs p port at the bottom of
this string.   Most of us think p  port is the way to go.  Plenty of
power, simplicity, no danger of detonating.  You can p port the Renesis
for far less money than buying a Mistral turbo. Next message I will post
at the bottom of the string so that we are all doing it the same.

Jerry

I put him on the list before I sent the message Jerry. Hopefully
he got it then.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.