Subject: P-Port Housings for 20B
From: Rotary Engine
Date: 12/28/2007, 3:05 PM
To: AARotary Engine



Hi Paul,
My 20B project has gotten delayed for the last 9 months while trying to
build a house, but I'm back at it now.  I've decided to go normally
aspirated P-Port, but as I started looking for P-Port Housings, I became
concerned about which housing are correct for the 20B.  Racing Beat has
several p-port housing available but of course none say they are for the
20B.  The ones listed are:

1)  Peripheral Port Housings 1986-92 Racing Beat 13B Non-turbo
2)  Peripheral Port Housings 1986-92 Racing Beat 13B Turbo
3)  Peripheral Port Housings 1974-1985 Racing Beat 13B Non-turbo
4)  Peripheral Port Housings 1974-1985 Racing Beat 13B Turbo

Which one is the most appropriate for the 20B?  Or, is it better to have
someone convert my original housings?  I was planning on using the 89-91
NA high compression rotors (9.7:1).  If machining my housings is best,
who can do a quality machining job of this for me?

Secondly, I'm trying  to decide on 2mm -vs- 3mm Apex seals.  What are
your thoughts on this for  normally aspirated P-Port aircraft
application?  If 3mm is best, again, who can do a quality machining job
of this for me?

Thanks again for all your knowledge and expertise!!
Don Mitchell


Number 2 is best but I am sure they are more money.
If you had your current housings done Jim Poole can bore
the holes but then you would need someone to weld them and finish
the the minor porting required. Mazdatrix are capable of the whole
job so you might check with them. Two mm stock apex seals are fine.
All stock seals are now two piece and based on RX8 technology.
I don't recommend after market apex seals except for Ianette ceramic.
No one has the capabilities to make them correctly and some
can wear out your rotor housings sooner rather than later.

Paul Lamar ...No rotor no motor.

Paul,
Why the Turbo housings? I thought the non- turbo with higher compression
ratio would be best. I guess it all depends of what power you were wanting
and if you intended using a turbo or not!

Don the 3mm will withstand a little detonation (so I'm told- no first hand
knowledge) but don't seal as well as the 2mm, but if you were wanting to use
a turbo and wanted a little more insurance against detonation use the 3mm.
If your wanting more compression use the RX8 rotors, but they have their own
set of problems with short side seals.

If you can afford the factory PP it would save a fair bit of work if you do
it yourself, and may be cheaper than having it done. What are they asking
for a factory PP and are they new?
George (down under)

-------------------------------------------------------------------

The rotor housings have nothing to due with the compression ratio
George. The rotor controls the compression ratio. You know that :)
The late turbo rotor housings have a cooling enhancement
modification.
Paul Lamar

Paul,
Yep I know that, I wasn't thinking - I do that sometimes. As soon as I read
turbo and non-turbo, I though compression - silly me!!

That was very interesting info, although I was going cross eyed trying to
read page 111 - any chance of getting that again?

I notice what I consider a typo in the 'key-to-steel' under acicular cast
iron. They mention a carbon content of about 3,0%, I'm guessing they mean
0.3% as not much goes over 1.0% as the benefits are greatly diminished over
1%.

George (down under)

http://www.key-to-steel.com/Articles/Art63.htm

"Cast iron has higher carbon and silicon contents than steel. Because
of the higher carbon content, the structure of cast iron, as opposed
to that of steel, exhibits a rich carbon phase. Depending primarily
on composition, cooling rate and melt treatment, cast iron can solidify
according to the thermodynamically metastable Fe-Fe3C system or the
stable Fe-Gr system.

When the metastable path is followed, the rich carbon phase in the
eutectic is the iron carbide; when the stable solidification path
is followed, the rich carbon phase is graphite. Referring only to
the binary Fe-Fe3C or Fe-Gr system,

cast iron can be defined as an iron-carbon alloy with more than 2% C.

Important notice is that
silicon and other alloying elements may considerably change the
maximum solubility of carbon in austenite (g). Therefore, in
exceptional cases, alloys with less than 2% C can solidify with
a eutectic structure and therefore still belong to the family
of cast iron. "

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.