Subject: New tricks to detect knock onset - and cracks on seals
From: Rotary Engine
Date: 2/6/2008, 4:48 PM
To: AARotary Engine




   From:
   http://www.worldcarfans.com/2070322.001/new-bmw-m3-v8-engine-in-detail


   An outstanding highlight in engine management: ion flow technology

   A particular highlight in engine management is ion flow technology
   detecting any knocking in the engine as well as the risk of misfiring or
   miscombustion. Contrary to conventional processes and technologies, this
   function is now performed directly where it counts, that is right there
   in the combustion chamber itself. To provide this highly efficient
   control, each cylinder is monitored and controlled via the spark plug to
   determine any knocking tendency. At the same time the system checks the
   ignition for smooth and correct operation, and recognises any misfiring.

   The spark plug therefore serves as an actuator for the ignition and as a
   sensor observing the combustion process, distinguishing in this way
   between mis-combustion and misfiring. And through this double function
   performed by the spark plug, diagnostic requirements in maintaining and
   servicing the engine are also facilitated.


   Previously, i think the methods to detect knock have been piezo
   detectors on cylinder/rotor head that listen to 6000-8000 Hz knock
   signature, EGT/CHT trend monitoring, and pressure sensors routed to
   chamber eg. thru spark plug body.
   This new method seems to be quite reliable and can be implemented easily
   to ECU boxes that have ignition control.

   This leads to think..
   How apex seals will hold together when engine is on dyno and repeatedly
   run against knock limit - to create clear figure where the limits
   (schlimits!) are....

   If seal has got cracks, it is likely that it's resonant frequency will
   change - just like it happens with eg. wine glass..

   Testing might be done - without engine breakdown - by fabricating a
   probe that attach to spark plug hole and contact seal when it is rotated
   on position. Then probe will test it's integrity by exciting it with
   sound sweep, and monitoring response when sweeping through it's normal
   resonant freq.

   Small surface cracks don't necessarily create big difference, but
   depending on which mode the seal is vibrating the change in part
   stiffness might be detectable.

   Cheers,

   Petri


   Saab was fooling around with this quite a few years ago as I recall.
   Also you want to monitor the intake air temperature and keep it below
   about 140 F. When the intake air/fuel mixture is compressed 10 to 1
   by the engine
   and or a turbo charger the temperature rises. It can self ignite
   before top
   dead center by the increase in heat due to the compression. The
   piezo knock
   detectors  are after the fact.

   One should be looking for a knock or self ignition predictor. The intake
   temperature is the best predictor I have found so far. This was
   known prior
   to WW II and P38 pilots were trained to monitor the intake air temp.

   Paul Lamar

Peak chamber pressure timing (measured by ion sensing or with a direct
pressure sensor (less practical)) should dictate ignition timing -
regardless of temperature.  This will keep the engine from detonating
(or even pre-igniting) if the detonation is at all controllable by
ignition timing.  (If the boost pressure*temperature gets high enough,
the ignition timing won't have any effect at controlling detonation -
the engine just diesels above a certain P*T. )

That's the beauty of measuring the timing of the pressure peak.  It
keeps you from getting to a place where the engine knocks.
Fortuitously, the timing that leads to peak horsepower (torque at a
given RPM) is one which is cooler (more retarded) than one which causes
the onset of pre-ignition.  This means that while on the dyno, you rock
the timing to get the best horsepower and measure the timing of the
associated pressure peak.  You don't have to drive the engine into
knock/pre-ignition.  Amazingly, as pressure and temperature vary, the
best horsepower chamber pressure timing doesn't vary, though the
ignition timing angle required to achieve that does..

Peak boost pressure should be limited by intake temperature - separate
Picaxe on the wastegate from the Picaxe controlling timing.  This will
keep from getting to an operating condition (P*T) where retarding the
spark doesn't have any control over detonation.

An absolute pressure pop-off valve is useful in case the throttle is
rapidly closed.


Regards,

Matt-

Some of the 1998 SAAB work.
http://www.fs.isy.liu.se/~larer/Projects/main.html
http://www.swri.org/3pubs/ird2003/synopses/039305.htm
http://www.theautochannel.com/news/2001/04/20/018974.html
http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO2&Sect2=HITOFF&p=1&u=%2Fnetahtml%2FPTO%2Fsearch

For some strange reason my browser does not like the www.USPTO.gov plug in required
for illustrations so I would appreciate it if some one would screen capture
them and send them to me.

Paul Lamar



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.