Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/25/2008, 6:16 AM
To: AARotary Engine


         >>> Can someone one the list  point me toward a
         >>> rugged, NASCAR type, oil to
         >>> water heat exchanger AND the heat transfer
         >>> coefficient data for it?
         >>>
         >>> Thanks,
         >>> Aubrey Thompson
         >>>
         >>> Do you have Compact Heat Exchangers Aubrey?
         >>> Lots of theory
         >>> and coef.'s.
         >>>
         >>> As far as hardware is concerned I was unaware
         >>> NASCAR race cars used
         >>> oil/water
         >>> heat exchangers. I see one small one on ebay
         >>>
         >>> Something to do with cooling the valve
         >>> springs?
         >>> Sounds like a good idea if they are breaking
         >>> due to heat:)
         >>>
         >>> Here are some sources.
         >>>
         >>>
         >> http://www.crracing.com/custom_built/external_heat.shtml
         >>> http://www.sen-dure.com/
         >>> http://www.trola.com/prod_standard.asp
         >>>
         >>> http://www.mkivsupra.net/vbb/showthread.php?t=139765
         >>> http://www.amfmotorsports.com/prod/cr1.1.htm
         >>>
         >>> Put  "oil to water heat exchanger" in google
         >>> advanced search.
         >>>
         >>> Paul Lamar
         >>>
         >>> Aubrey,
         >>>
         >>> Also, try Fluidyne.  They make lots of custom and
         >>> racing stuff.
         >>>
         >>> Mark S.
         >>>
         >>>
         >>> Aubrey,
         >>> The ford trucks with a 5.4 with the towing package
         >>> have an oil to water heat
         >>> exchanger. Unit works well and you should be able to
         >>> find one at a good
         >>> price at a salvage yard. The Expeditions with the
         >>> tow package also have it.
         >>> Larry
         >>
         >>
         >>
         >>
         >> Aubrey
         >>
         >> I have this one reputed to be from a Ford Crown Vic or
         >> maybe a police car. It has a cast alum shell, inside
         >> looks like radial fins, wt is 5#. Braided lines look
         >> to be oem.
         >> regards, Robert
         >>
         >>
         >> Some of the car racers are are building their own.
         >> They take a stock oil to air heat exchangers (oil cooler) and
        weld it
         >> inside a box. The box is then plumbed to the water supply.
         >>
         >> Lets say your water cooling system is marginal. For most Mazda
        rotary
         >> installations that is probably true. It won't get any better if
        you add the
         >> oil cooler
         >> heat load to the water cooling system. It can only get worse. If
        you get a
         >> leak and you dump all the glycol coolant overboard you will have
        less time
         >> to get the airplane on the ground as the oil will over heat
    as well.
         >> The engine may seize due to overheated melted e-shaft bearings.
         >>
         >> With an air to oil cooling system it is working in parallel. You
        still
         >> have one third of the overall engine cooling and you may have
        more time to
         >> get the airplane on the ground.
         >>
         >>
         >> Paul Lamar
         >
         >
         > Laminova, Laminova, Laminova...
         >
         > http://www.thinkauto.com/laminova.htm
         >
         > I forget the name of the parent company, but their website isn't
        much better
         > than this link.  Not cheap, IMHO not a good idea, but deffinately
        the only
         > thing to think of for an aircraft installation where size,
        weight, and
         > efficiency is at a premium.
         >
         > Tom Lee

        Tom,

        Size, weight and location are advantageous perhaps, but as for
        efficiency I
        am not so sure.  When the water temperature is below 85 degrees, OK
        sure.
        Marine applications are like this but they dump the BTU overboard
        along with
        the cooling water. In  aviation more than likely on T.O,  when
        cooling loads
        and engine stress are greatest, the water temp. is going to be over
        185F.

        With oil temps. at 200F + degrees, the delta T to water will
    only be 15
        degrees, 200 minus 185 degrees.  If we use an oil-to-air heat
        exchanger, the
        delta T with an 85 degree ambient air temperature would be 200F
        minus 85F or
        115F degrees.

        Heat moves towards the lower potential, so a higher difference in
        temperature  (higher delta T) would result in a higher rate of heat
        transfer
        and be more efficient.  Of course this entails designing proper
        intake and
        exhaust ducts  (Paul's forte') that insures all of those fins on the
        oil-to-air heat exchanger are free of insulating air boundary
        layers, and
        whole air mass moves through the duct in a timely and orderly
    fashion.
        The same criteria applies to the water to air heat exchanger.

         As for why Ford trucks would offer the oil-to-water-to-air heat
        exchanger
        in a towing application where the engine is under a heavy duty
    cycle I
        haven't a clue.  Perhaps someone could explain it to me.  Keeping
        the engine
        oil warm in the cold north? :)


        Doug in Japan

        One factor is the small amount of heat transfered to the oil in most
        piston engines. Some piston engine squirt oil
        at the under side of the piston to cool them. Many aircraft piston
        engines do this as do some diesels. Never the less the heat
    dissipated
        by the oil is usually less than 10% of the total.

        The rotary on the other hand has this oil cooled rotor that forms
        about half
        of the area of the combustion chamber. This results in one third
        of the total heat rejection to the cooling system. As you can see,
        from this
        heat balance chart, 50 HP or 25% of the HP out of the e-shaft during
        lean cruise is rejected
        by the oil heat alone. At rich mixtures, typical during take off and
        climb out, the
        percentage becomes greater. If the oil is cooler than the
        glycol coolant it is not a good idea to transfer heat to the oil
        from the glycol.
        One needs to delay heating the oil as long as possible with a good
        oil to air
        heat exchanger and proper air ducting. More oil helps this process
        as it takes more heat to
        heat a larger quantity of oil. The difficult history of the Mazda
        rotary installation
        in aircraft has been mostly about keeping it cool both oil and
    glycol.

        Paul Lamar ...No rotor no motor.

    Doug,
    I'm running an oil-to-water exchanger on my 3-rotor.  I think one of the
    keys to whether or not this works is where you tap the water to feed the
    exchanger.  I drilled & tapped a 1/2" NPT on the high pressure side of
    the water pump housing, just prior to where the coolant enters the
    engine.  Then I returned the heated water to the engine out (radiator
    inlet).  By doing it this way the water temp feeding the oil-to-water
    exchanger is much lower which increases the delta T across the
    exchanger.   It also increases the delta-t across the radiator by
    dumping more btu's into the system.

    Paul stated that the "difficult history of the Mazda rotary installation
    in aircraft has been mostly about keeping it cool both oil and glycol."
    The beauty of using the oil to water exchanger is that it tends to keep
    the oil and water within about 10* of each other.   Before adding the
    oil-to-water exchanger, my oil temps would run much higher than the
    water temps.

    BTW Paul, I flew today and checked the CHT's.  In an economy cruise they
    were around 180-185*F.  The one nearest the water pump was the coolest,
    the one nearest the flywheel was the hottest, as you would expect.  One
    of these days I'll think to check the CHT's during climb.

    Mark S.
    27.1 hrs

    What was the outside air temp? How fast and long did you climb out?
    What was the climb rate FPM? What was the oil and glycol temperature
    just before you took off?

    It's still winter in Austin TX. A one degree increase in ambient
    temperature
    is a one percent reduction in cooling capacity. Let me know when you
    fly in
    100 F ambient air temperatures :) I am not saying it won't work but
    there is
    X amount of heat to be dissipated. If you put it all in the glycol
    system
    the glycol system MUST be 1/3rd  larger than it would need to be if
    it were
    just doing glycol. There is no free lunch. It is just common sense.

    Take some data and don't forget to record the ambient temperature
    and the
    climb speed. Many people quote temps but they neglect to measure or
    mention
    the out side air temperature and the climb speed.

    A marginal cooling system will work if you climb out at 200 FPM at
    130 to 150 MPH to 500  foot altitude. Texas is fairly flat in your area.

    Record temp out of the pump, out of the block, in the rad, OUT of
    the rad,
    in the oil water HX, out of the oil water heat HX, climb speed,
    climb duration
    and last but not least the all important out side air temperature.

    This should give everybody a clue on just how complicated this
    system is.
    That is why I wrote a book on the subject.

    The situation with an air cooled engine is not as bad as the
    rate of heat transfer from cylinder fins to air is greater and as the
    fins heat up beyond 400 or 500 F the rate of heat transfer also
    increase.

    With a water cooled system there is a real limit of how hot the glycol
    can become before catastrophic boil over. The air/oil cooler is not
    as bad
    as the boiling temp of oil is much much higher than that that of
    glycol.

    Paul Lamar ...No rotor no motor.

Paul,
Here's a little more data (from memory).

Climb was at 100 kts [115 MPH] , 1100 fpm from 520 ft to 1500 ft, then 800 fpm up to
3000 msl at 115 kts [132].  Once I reach 500' agl I start reducing the prop
rpm.  For yesterday's flight prop rpm was set at 2300 for takeoff.
During the 800 fpm climb the oil temp was up to 205 and water temp was
195.

OAT on the ground was 75, it was a beautiful, cloudless day.  (Today
they're predicting a high of 87*... so much for the Texas winters)
I don't have all the other readings as I don't have that many inputs on
my EFIS.  But I do monitor the oil temp out of the engine (pre oil/air
cooler) and oil temp pre oil/water cooler.

One thing I'm not sure you realize with my cooling system is that I
still have the oil-to-air exchanger installed.  I was hoping that there
would be enough capacity in the water radiator to handle the whole
cooling load, but that was not the case.  The oil/air exchanger is in
series with the oil/water exchanger.  So, I left it in place and feed
the hottest oil to that cooler first, then run it through the
oil-to-water cooler to bring it down another 25*.  It was pretty obvious
from the start that I had an excess of water cooling capacity and a
deficiency of oil cooling.  So, all I'm doing is transferring some of
the load from the oil to the water.  If I could increase the cooling
capacity of the oil/air exchanger I probably wouldn't need the oil/water
exchanger.

Mark S.

I went back and checked some old messages prior to installing the oil water
HX but you never mentioned OAT or climb. Do you remember what that may have
been?

"To answer your question on water temps; the water temps were never a problem.
They would stabilize around 135-150, depending on MAP."

Sounds like your glycol system was very effective if not over kill.
Do you recall the size of the rad?

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.