Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/25/2008, 2:29 PM
To: AARotary Engine


               Tom,

               Size, weight and location are advantageous perhaps, but
   as for
               efficiency I
               am not so sure.  When the water temperature is below 85
       degrees, OK
               sure.
               Marine applications are like this but they dump the BTU
       overboard
               along with
               the cooling water. In  aviation more than likely on T.O,
    when
               cooling loads
               and engine stress are greatest, the water temp. is going to
       be over
               185F.

               With oil temps. at 200F + degrees, the delta T to water will
           only be 15
               degrees, 200 minus 185 degrees.  If we use an oil-to-air
   heat
               exchanger, the
               delta T with an 85 degree ambient air temperature would
   be 200F
               minus 85F or
               115F degrees.

               Heat moves towards the lower potential, so a higher
       difference in
               temperature  (higher delta T) would result in a higher rate
       of heat
               transfer
               and be more efficient.  Of course this entails designing
   proper
               intake and
               exhaust ducts  (Paul's forte') that insures all of those
       fins on the
               oil-to-air heat exchanger are free of insulating air
   boundary
               layers, and
               whole air mass moves through the duct in a timely and
   orderly
           fashion.
               The same criteria applies to the water to air heat
   exchanger.

                As for why Ford trucks would offer the
   oil-to-water-to-air heat
               exchanger
               in a towing application where the engine is under a
   heavy duty
           cycle I
               haven't a clue.  Perhaps someone could explain it to me.
        Keeping
               the engine
               oil warm in the cold north? :)


               Doug in Japan

               One factor is the small amount of heat transfered to the oil
       in most
               piston engines. Some piston engine squirt oil
               at the under side of the piston to cool them. Many aircraft
       piston
               engines do this as do some diesels. Never the less the heat
           dissipated
               by the oil is usually less than 10% of the total.

               The rotary on the other hand has this oil cooled rotor that
       forms
               about half
               of the area of the combustion chamber. This results in
   one third
               of the total heat rejection to the cooling system. As you
       can see,
               from this
               heat balance chart, 50 HP or 25% of the HP out of the
       e-shaft during
               lean cruise is rejected
               by the oil heat alone. At rich mixtures, typical during take
       off and
               climb out, the
               percentage becomes greater. If the oil is cooler than the
               glycol coolant it is not a good idea to transfer heat to
   the oil
               from the glycol.
               One needs to delay heating the oil as long as possible with
       a good
               oil to air
               heat exchanger and proper air ducting. More oil helps this
       process
               as it takes more heat to
               heat a larger quantity of oil. The difficult history of the
       Mazda
               rotary installation
               in aircraft has been mostly about keeping it cool both
   oil and
           glycol.

               Paul Lamar ...No rotor no motor.

           Doug,
           I'm running an oil-to-water exchanger on my 3-rotor.  I think
       one of the
           keys to whether or not this works is where you tap the water to
       feed the
           exchanger.  I drilled & tapped a 1/2" NPT on the high pressure
       side of
           the water pump housing, just prior to where the coolant
   enters the
           engine.  Then I returned the heated water to the engine out
       (radiator
           inlet).  By doing it this way the water temp feeding the
       oil-to-water
           exchanger is much lower which increases the delta T across the
           exchanger.   It also increases the delta-t across the
   radiator by
           dumping more btu's into the system.

           Paul stated that the "difficult history of the Mazda rotary
       installation
           in aircraft has been mostly about keeping it cool both oil and
       glycol."
           The beauty of using the oil to water exchanger is that it tends
       to keep
           the oil and water within about 10* of each other.   Before
       adding the
           oil-to-water exchanger, my oil temps would run much higher
   than the
           water temps.

           BTW Paul, I flew today and checked the CHT's.  In an economy
       cruise they
           were around 180-185*F.  The one nearest the water pump was the
       coolest,
           the one nearest the flywheel was the hottest, as you would
       expect.  One
           of these days I'll think to check the CHT's during climb.

           Mark S.
           27.1 hrs

           What was the outside air temp? How fast and long did you
   climb out?
           What was the climb rate FPM? What was the oil and glycol
   temperature
           just before you took off?

           It's still winter in Austin TX. A one degree increase in ambient
           temperature
           is a one percent reduction in cooling capacity. Let me know
   when you
           fly in
           100 F ambient air temperatures :) I am not saying it won't
   work but
           there is
           X amount of heat to be dissipated. If you put it all in the
   glycol
           system
           the glycol system MUST be 1/3rd  larger than it would need
   to be if
           it were
           just doing glycol. There is no free lunch. It is just common
   sense.

           Take some data and don't forget to record the ambient
   temperature
           and the
           climb speed. Many people quote temps but they neglect to
   measure or
           mention
           the out side air temperature and the climb speed.

           A marginal cooling system will work if you climb out at 200
   FPM at
           130 to 150 MPH to 500  foot altitude. Texas is fairly flat in
       your area.

           Record temp out of the pump, out of the block, in the rad,
   OUT of
           the rad,
           in the oil water HX, out of the oil water heat HX, climb speed,
           climb duration
           and last but not least the all important out side air
   temperature.

           This should give everybody a clue on just how complicated this
           system is.
           That is why I wrote a book on the subject.

           The situation with an air cooled engine is not as bad as the
           rate of heat transfer from cylinder fins to air is greater and
       as the
           fins heat up beyond 400 or 500 F the rate of heat transfer also
           increase.

           With a water cooled system there is a real limit of how hot the
       glycol
           can become before catastrophic boil over. The air/oil cooler
   is not
           as bad
           as the boiling temp of oil is much much higher than that that of
           glycol.

           Paul Lamar ...No rotor no motor.

       Paul,
       Here's a little more data (from memory).

       Climb was at 100 kts [115 MPH] , 1100 fpm from 520 ft to 1500 ft,
       then 800 fpm up to
       3000 msl at 115 kts [132].  Once I reach 500' agl I start reducing
       the prop
       rpm.  For yesterday's flight prop rpm was set at 2300 for takeoff.
       During the 800 fpm climb the oil temp was up to 205 and water
   temp was
       195.

       OAT on the ground was 75, it was a beautiful, cloudless day.  (Today
       they're predicting a high of 87*... so much for the Texas winters)
       I don't have all the other readings as I don't have that many
   inputs on
       my EFIS.  But I do monitor the oil temp out of the engine (pre
   oil/air
       cooler) and oil temp pre oil/water cooler.

       One thing I'm not sure you realize with my cooling system is that I
       still have the oil-to-air exchanger installed.  I was hoping
   that there
       would be enough capacity in the water radiator to handle the whole
       cooling load, but that was not the case.  The oil/air exchanger
   is in
       series with the oil/water exchanger.  So, I left it in place and
   feed
       the hottest oil to that cooler first, then run it through the
       oil-to-water cooler to bring it down another 25*.  It was pretty
   obvious
       from the start that I had an excess of water cooling capacity and a
       deficiency of oil cooling.  So, all I'm doing is transferring
   some of
       the load from the oil to the water.  If I could increase the cooling
       capacity of the oil/air exchanger I probably wouldn't need the
   oil/water
       exchanger.

       Mark S.

       I went back and checked some old messages prior to installing the
       oil water
       HX but you never mentioned OAT or climb. Do you remember what that
       may have
       been?

       "To answer your question on water temps; the water temps were never
       a problem.
       They would stabilize around 135-150, depending on MAP."

       Sounds like your glycol system was very effective if not over kill.
       Do you recall the size of the rad?

       Paul Lamar ...No rotor no motor.


   Paul,
   The application was Ford Galaxy (probably w/390ci engine, but not
   stated).  Core size is 18 x 22.5 x 2.5, best I recall.  Initial flight
   was in August and the temps were in the mid 90's.

   Mark S.


   You obviously did a great job on the rad ducting. Core volume appears to
   be about 1000 cubic inches where our rule of thumb call for 300
   cubic inch
   per rotor or about 900 at the max for a 3 rotor.

   What I can't understand is why the oil cooler is not working better.
   Perhaps you have some air leaks in the front duct or the back side
   of the oil
   cooler is too hot. Can you make some air temps measurements behind
   the oil cooler?
   What brand of oil cooler is that?
   --
   Paul Lamar ...No rotor no motor.


Paul,
The exhaust manifold is now shielded with 321ss so the oil exchanger
should see minimal radiated heat.  My guess is that the water radiator
duct is working so well it is pressurizing the cowl and inhibiting the
air flow through the oil cooler.  Could the location of the water inlet
be slightly higher pressure than that of the oil cooler inlet?  Does oil
cooler's higher fin density drop the pressure even further?  Whatever
the answer, I believe the water radiator is flowing more than its share
of air and is causing the oil cooler to choke.

Another thing, after first flight the oil temps were 240*+ even on
shallow climb.  Obviously, this would not do for hot Texas summers.  The
first thing I did was to increase the cowl exit area.  That helped some
(supporting the above theory).  I put a baffle along the lower edge of
the oil exchanger because the exit air from the oil cooler was at a 90*
angle to the air exiting the water radiator.  This seemed to help a
little.  Still, I couldn't climb at full power on a 90+ day due to high
oil temps.  I guess I could have added a second oil/air cooler on the
other inlet, but it seemed worth a try to take advantage of some of the
excess water cooling capacity with the oil/water exchanger.  My only
regret is that there isn't enough excess cooling capacity that would
allow me to remove the oil/air exchanger completely.

Mark S.

What are the core dimensions for the oil cooler and the brand name.
Is it new? It sure looks big enough. Fins per inch and tubes per inch
are a good way to characterize heat exchangers.

Cut the water supply to the oil/water  HX during cruise and put a couple
of cowl flaps on it to warm the water. Engine eff. will go up.
That is perhaps as much as .02 down on the BSFC and .2 to .4 on the GPH.
There will be less aero cooling drag so MPG will go up significantly.

Matt may have hit on something by using a dedicated exit duct and cowl flap
for the oil cooler. It could converge down to the area of the scoop or less.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.