Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/25/2008, 7:09 PM
To: AARotary Engine



               I went back and checked some old messages prior to
       installing the
               oil water
               HX but you never mentioned OAT or climb. Do you remember
       what that
               may have
               been?

               "To answer your question on water temps; the water temps
       were never
               a problem.
               They would stabilize around 135-150, depending on MAP."

               Sounds like your glycol system was very effective if not
       over kill.
               Do you recall the size of the rad?

               Paul Lamar ...No rotor no motor.


           Paul,
           The application was Ford Galaxy (probably w/390ci engine,
   but not
           stated).  Core size is 18 x 22.5 x 2.5, best I recall.  Initial
       flight
           was in August and the temps were in the mid 90's.

           Mark S.


           You obviously did a great job on the rad ducting. Core volume
       appears to
           be about 1000 cubic inches where our rule of thumb call for 300
           cubic inch
           per rotor or about 900 at the max for a 3 rotor.

           What I can't understand is why the oil cooler is not working
   better.
           Perhaps you have some air leaks in the front duct or the
   back side
           of the oil
           cooler is too hot. Can you make some air temps measurements
   behind
           the oil cooler?
           What brand of oil cooler is that?
           --
           Paul Lamar ...No rotor no motor.


       It appears the oil cooler and glycol cooler exhaust into the same
       chamber/plenum (main volume of the cowl..  If the delta-P across
   the oil
       cooler is larger than the delta-P for the glycol cooler, it might
       explain the difference.  Maybe the oil cooler is thicker?  Is
   there room
       for a dedicated duct for the oil cooler to the outside of the cowl -
       maybe out the left side adjacent and aft of the cooler?


       Regards,

       Matt-


   Matt,
   Yes, the oil cooler is 3/8" thicker than the glycol exchanger.  Also,
   maybe more significant, is that the fin count is much higher for the oil
   cooler, resulting in higher drag/pressure drop across it.  I had
   considered adding a dedicated exit duct for the oil cooler, but didn't
   want to pay the drag penalty.  That's when I decided to try the
   oil-to-water exchanger.  The beauty with that solution is that it didn't
   cost me any additional cooling drag. I feel that if I could fit a
   slightly larger glycol exchanger in place of what I'm running now, that
   I could eliminate the oil/air exchanger altogether.  I even flew with
   50% of the oil/air exchanger blocked off.  It was pretty close with the
   current glycol exchanger, but not quite enough to fly in Texas in the
   summertime.  So, I left the oil/air exchanger in place and don't have
   any more cooling problems.  That's a real good feeling.

   Mark S.


   The Rotary Engine NewsLetter. Powered by Linux.
   ACRE NL web site. http://www.rotaryeng.net
   Copyright 1998-2007 All world wide rights reserved.


Mark,

So you're not interested in the cooling redundancy that Paul has
suggested as a good idea - using oil-air and glycol-air exchangers at
the same time?  I still think that would be the direction I'd go.  In
fact, I'd make that a requirement, as I think it's something that could
make for a more favorable outcome should the airplane suffer from a
single component failure..

Maybe it's just anecdotal, but the vaunted P-51 Mustang has a separate
oil-air cooler, as I believe do the other Merlin powered aircraft
(Spitfires, Hurricanes, etc).  I think the P-40 (Allison powered) was
the same way.

The Mustang had an induction air to glycol supercharger intercooler, but
this ran with a separate cooling loop from the engine - and had its own
coolant pump and air-glycol exchanger.  This allowed putting the
intercooler where the directness/compactness/packaging is important.  It
wouldn't be practical to have a duct feeding an air-air intercooler
between the stages of the supercharger (on a Merlin).

Please keep in mind, I don't have a rotary powered airplane, nor a
liquid cooled airplane, nor even an airplane I built myself, so take my
ideas with a grain of salt..  :)

I also commend you for putting together an airplane that's running
well.  I admire the accomplishment.


Regards,

Matt-


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.