Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/25/2008, 7:13 PM
To: AARotary Engine



               I went back and checked some old messages prior to
       installing the
               oil water
               HX but you never mentioned OAT or climb. Do you remember
       what that
               may have
               been?

               "To answer your question on water temps; the water temps
       were never
               a problem.
               They would stabilize around 135-150, depending on MAP."

               Sounds like your glycol system was very effective if not
       over kill.
               Do you recall the size of the rad?

               Paul Lamar ...No rotor no motor.


           Paul,
           The application was Ford Galaxy (probably w/390ci engine,
   but not
           stated).  Core size is 18 x 22.5 x 2.5, best I recall.  Initial
       flight
           was in August and the temps were in the mid 90's.

           Mark S.


           You obviously did a great job on the rad ducting. Core volume
       appears to
           be about 1000 cubic inches where our rule of thumb call for 300
           cubic inch
           per rotor or about 900 at the max for a 3 rotor.

           What I can't understand is why the oil cooler is not working
   better.
           Perhaps you have some air leaks in the front duct or the
   back side
           of the oil
           cooler is too hot. Can you make some air temps measurements
   behind
           the oil cooler?
           What brand of oil cooler is that?
           --
           Paul Lamar ...No rotor no motor.


       Paul,
       The exhaust manifold is now shielded with 321ss so the oil exchanger
       should see minimal radiated heat.  My guess is that the water
   radiator
       duct is working so well it is pressurizing the cowl and
   inhibiting the
       air flow through the oil cooler.  Could the location of the
   water inlet
       be slightly higher pressure than that of the oil cooler inlet?
    Does oil
       cooler's higher fin density drop the pressure even further?
    Whatever
       the answer, I believe the water radiator is flowing more than
   its share
       of air and is causing the oil cooler to choke.

       Another thing, after first flight the oil temps were 240*+ even on
       shallow climb.  Obviously, this would not do for hot Texas
   summers.  The
       first thing I did was to increase the cowl exit area.  That
   helped some
       (supporting the above theory).  I put a baffle along the lower
   edge of
       the oil exchanger because the exit air from the oil cooler was
   at a 90*
       angle to the air exiting the water radiator.  This seemed to help a
       little.  Still, I couldn't climb at full power on a 90+ day due
   to high
       oil temps.  I guess I could have added a second oil/air cooler
   on the
       other inlet, but it seemed worth a try to take advantage of some
   of the
       excess water cooling capacity with the oil/water exchanger.  My only
       regret is that there isn't enough excess cooling capacity that would
       allow me to remove the oil/air exchanger completely.

       Mark S.

       What are the core dimensions for the oil cooler and the brand name.
       Is it new? It sure looks big enough. Fins per inch and tubes per
   inch
       are a good way to characterize heat exchangers.

       Cut the water supply to the oil/water  HX during cruise and put
   a couple
       of cowl flaps on it to warm the water. Engine eff. will go up.
       That is perhaps as much as .02 down on the BSFC and .2 to .4 on
   the GPH.
       There will be less aero cooling drag so MPG will go up
   significantly.

       Matt may have hit on something by using a dedicated exit duct and
       cowl flap
       for the oil cooler. It could converge down to the area of the scoop
       or less.

       Paul Lamar ...No rotor no motor.


   Paul,
   The oil cooler is made by Fluidyne.  As I recall, it is 11 x 9.5 x
   2-7/8.  It is a dual pass and has turbulators inside the tubes.

   The dedicated exit duct sounds like it could work.  I'll give it some
   thought.  Its hard messing with success though.

   A question... would an equivalent sized dual pass glycol exchanger work
   better than what I now have.  I'm referring to the design that puts two
   cores back to back.  If so, do you think it would dissipate enough heat
   to handle both the total heat load of a 3-rotor?

   Mark S

   The heat transfer from oil to metal is not as good as from
   Glycol to metal. That is why some oil coolers have turbulators.
   That is also why oil is not used as the primary coolant.
   It would be great if it did as the boiling temperature is much higher.

   This chart is from Bill Schertz.
   IMHO the thermal Conductivity Coefficient column is what is really
   pertinent.
   As you can see water (.392) is the best. 50/50 glycol (.262) is not
   as good and oil is way down the list. Pure glycol is (.135).
   It appears to be inversely proportional to viscosity but
   maybe not.

   Bill do you have any similar units data for oils?
   My guess is it is .10 based on the ratio of these  units.

   http://www.engineeringtoolbox.com/thermal-conductivity-d_429.html

   Oil, machine... 0.15
   Olive oil...... 0.17
   Water.......... 0.58
   Kerosene ...... 0.15


   Mark, You should wait until the heat of summer hits before you
   change anything.

   BTW guys please set your left margins to 0 in your email editor
   programs.

   Paul Lamar ...No rotor no motor.


Paul,
Why wait until summer... it was 92* here in Austin today.

Mark S.

That was today. Tomorrow it will be 65 again :)
I lived in Midland for awhile. There was nothing between Midland
and the North Pole except for a few barb wire fences :)

During summer you get a nice long hot spell where you can make
changes and try them from day to day.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.