> > > >> The more I think about a low conduction SS rotor the better
> > > it looks.
> > > >> I suspect
> > > >> a disproportionate amount of combustion heat is going into
> > > the rotor
> > > >> and thence into the oil raising the BSFC.
> > > > >
> > > > > Paul Lamar
> > > >
> > > > Make the new RX8 rotor also 7-8 CR, and we have a wonderful
> > > rotor for
> > > > turbo engine.
> > > > Cheers, Petri
> > > >
> > > > Good idea. We can sell them to the RX8 engine people with
> > a lower
> > > > compression ratio for turbo charging. The current 10:1 RX8
> > rotors > > are really unsuitable for turbo charging.
> > > > Paul Lamar
> > >
> > > Every RX8 tuner wants a pair of these. This could finance
> > the whole
> > > project.
> > > Things to take care of first could be:
> > >
> > > High rotor face temp on WOT.
> > > Lower thermal conductivity translates to higher surface temp?
> > > We don't want this on high boost. Makes the knock situation
> > > worse on
> > > high power, also volumetric efficiency would suffer, offsetting
> > > our gain
> > > on IMEP somewhat. But how much - and should we care?
> > >
> > > On 75% cruise, this is likely to be just fine. Together with
> > > 250F/16psiglycol-water coolant, there could be clear gains on
> > > BSFC compared to
> > > baseline engine.
> > >
> > > But car tuners are mainly interested on how much peak power
> > they could
> > > get, and that's the biggest market...
> > >
> > > Apex seal groove friction
> > > Boost stresses are higher due to 14-28 psi boost possible.
> > Is SS
> > > up to
> > > task by itself?
> > > Cheers,
> > > Petri
> > >
> > > Once the patterns are made you could cast either in iron or SS.
> > > If there was enough meat you could machine the combustion chamber
> > > on an NC mill. Make heavier high CR SS for the RX8 car cruise
> > > market with
> > > a lower red line. Make lighter low CR iron for the turbo RX8
> > market. >
> > > Paul Lamar
> >
> > What would be the weight of a SS rotor? Presently it is 9.2 pounds.
> >
> > Marc J.
> > NexusMustang
> >
> >
> >
http://hypertextbook.com/facts/2004/KarenSutherland.shtml
> >
> > Metal Steel, tool..........7.715
> > Metal Wrought Iron.........7.75
> > Metal Carbon Tool Steel....7.82
> > Metal Steel, cold-drawn....7.83
> > Metal Carbon Steel.........7.84
> > Metal Steel, C1020, HR.....7.85
> > Metal Pure Iron............7.86
> > Metal Soft Steel (0.06% C).7.87
> > Metal Stainless Steel, 304.8.03
> > Metal Stainless 18Cr-8Ni...8.03
> > --
> >
> > Very little difference.
> > It would all depend on the casting patterns
> > and how it was cast.
> > Modern RX8 rotors are centrifugally cast.
> >
> >
> > BTW does Andrea want to be on the list. I have
> > had no email from him?
> >
> > Paul Lamar ...No rotor no motor.
>
> Good morning Paul,
>
> André Julien from Pratt & Whittney wants to be contacted outside the
list.
>
> Just a small question regarding ceramic coating. That
> process, by adding ceramic would increase the compression ratio? Or the
> process remove a small layer of metal in order to add the ceramic?
>
> Marc J.
> NexusMustang
>
>
> OK
>
> Internal Ceramic coatings are very dangerous to the health of your
Mazda engine and
> do nothing. They are so thin that they will have minimal affect on
the CR.
>
> Paul Lamar ...No rotor no motor.
Dear Paul:
Since you wrote, in a thread entitled, "RotaMax fuel burn", October,
2007, concerning coatings:
"The people I have talked to that have built successful all aluminum
rotary engines swear the only thing that works well is silicon carbide
detonation gun coatings diamond ground. This is expensive. It is
what Mazda used on the Lemans four rotor. Many have tried other things
and have failed."
Can we make that one small caveat, to include silicon carbide detonation
gun coatings, diamond ground, as the sole acceptable coating?
Thanks,
Les :-)
That is absolutely right but it is done for a different reason.
It is a wear coating and it is silicon carbide. Probably not what
people are trying to use as insulation. IMHO there are only two reliable
choices for the wear surface. Cast in steel liner like Mazda does it
or det. gun coating.
Steve B what did you guys use?
IMHO people would be better off chrome plating the rotor to reflect
3000 F combustion heat and cut down on carbon build up.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.