Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/26/2008, 12:53 PM
To: AARotary Engine



       Mark,

       So you're not interested in the cooling redundancy that Paul has
       suggested as a good idea - using oil-air and glycol-air
   exchangers at
       the same time?  I still think that would be the direction I'd
   go.  In
       fact, I'd make that a requirement, as I think it's something
   that could
       make for a more favorable outcome should the airplane suffer from a
       single component failure..

       Maybe it's just anecdotal, but the vaunted P-51 Mustang has a
   separate
       oil-air cooler, as I believe do the other Merlin powered aircraft
       (Spitfires, Hurricanes, etc).  I think the P-40 (Allison
   powered) was
       the same way.

       The Mustang had an induction air to glycol supercharger
   intercooler, but
       this ran with a separate cooling loop from the engine - and had
   its own
       coolant pump and air-glycol exchanger.  This allowed putting the
       intercooler where the directness/compactness/packaging is
   important.  It
       wouldn't be practical to have a duct feeding an air-air intercooler
       between the stages of the supercharger (on a Merlin).

       Please keep in mind, I don't have a rotary powered airplane, nor a
       liquid cooled airplane, nor even an airplane I built myself, so
   take my
       ideas with a grain of salt..  :)

       I also commend you for putting together an airplane that's running
       well.  I admire the accomplishment.


       Regards,

       Matt-

   Matt,
   I do have a glycol-air and an oil-air exchanger, but also an oil-glycol
   exchanger.  I don't see where removing the oil-glycol exchanger is going
   to improve the time I have to get on the ground should the glycol system
   spring a leak.  I may explore the possibility of building a dedicated
   exit duct for the oil-air exchanger though... in my spare time.  If that
   works out, then I'll consider removing the oil-glycol exchanger.

   Mark S.

   I am really interested in why it is not working better. If you don't
   mind,
   next time you are out there, please record the number of fins per
   inch and the
   tube spacing. Also if you have a water manometer measure the pressure
   on the face of the oil cooler at speed. Use the porous foam hot glued to
   the end of the sense tube trick. You have my cooling book.

   Here is a chart of dynamic pressure verses speed. The pressure should be
   .3 to .4 of this number in the center of the core. If it is higher
   or lower
   there could be something wrong with the duct or the porosity of the
   oil cooler.

   In other words at 120 MPH dynamic pressure is 6.9 inches of water.
   The oil cooler face should be in the ball park of 2 to 2.8 inches of
   water.
   The higher the number the less the porosity of the oil cooler. If it is
   blocking the air flow through the core excessively it should be much
   higher
   than 2.8 inches.

   If it is lower than 2 inches you may have a leak in the duct or the
   duct may
   be improperly shaped.  You can do the same thing to the glycol rad
   and compare
   the two numbers. It would also be helpful to measure the pressure
   behind the core in the cowl as well.

   You would not happen to have any data like this on the oil cooler
   would you?

   My brain is kind of fried. Pardon the pun. Perhaps perhaps Bill
   Schertz can tell
   us where we want to be on the 3 rotor oil BTU rejection.

   Paul Lamar


Paul,

Won't the delta-P of the oil cooler be affected by the properties of the
glycol exchanger and its duct?  If the glycol portion has especially low
drag, I think the pressure inside the cowl will be relatively high (low
delta-P across glycol exchanger), making it look like there's something
wrong with the oil exchanger/duct.

I guess if you check the pressure on the front side of the glycol
exchanger, and in-cowl pressure, and compare all to ambient, you should
have a pretty good picture of where the air wants to go.

The inlet duct on the oil-air exchanger looks pretty good (geometry,
shape).  If it leaked air, that would lower the glycol-air exchanger
efficiency (that doesn't appear to be the issue) by raising the in-cowl
pressure.  So, it seems like the oil-air exchanger might not be well
matched to the glycol-air exchanger - when feeding a common outlet
chamber.  If this is the case, the only fix I can think of is to arrange
for an isolated outlet from the oil-air exchanger.  You could also block
a portion of the outlet of the glycol-air exchanger, but that seems so
wrong..  :)

Mark, is your cowl in final paint?  I think it would be pretty easy to
cut louvers aft of the oil-air exchanger, build a small outlet plenum
and connect it to the outlet of the oil-air exchanger with large
diameter scat tube.  Maybe it would look something like this:

http://www.cs-ent.ca/6578o.jpg

If it doesn't buy you anything, you wouldn't have spent much on it, and
they'd be easy to cover over later (assuming you aren't in final paint).


Regards,

Matt-

Best to put a small flap on there to keep the oil temp up
at high altitude cruise. Reduces the GPH.

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.