Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/26/2008, 1:35 PM
To: AARotary Engine



            Mark,

            So you're not interested in the cooling redundancy that Paul has
            suggested as a good idea - using oil-air and glycol-air
        exchangers at
            the same time?  I still think that would be the direction I'd
        go.  In
            fact, I'd make that a requirement, as I think it's something
        that could
            make for a more favorable outcome should the airplane suffer
    from a
            single component failure..

            Maybe it's just anecdotal, but the vaunted P-51 Mustang has a
        separate
            oil-air cooler, as I believe do the other Merlin powered
    aircraft
            (Spitfires, Hurricanes, etc).  I think the P-40 (Allison
        powered) was
            the same way.

            The Mustang had an induction air to glycol supercharger
        intercooler, but
            this ran with a separate cooling loop from the engine - and had
        its own
            coolant pump and air-glycol exchanger.  This allowed putting the
            intercooler where the directness/compactness/packaging is
        important.  It
            wouldn't be practical to have a duct feeding an air-air
    intercooler
            between the stages of the supercharger (on a Merlin).

            Please keep in mind, I don't have a rotary powered airplane,
    nor a
            liquid cooled airplane, nor even an airplane I built myself, so
        take my
            ideas with a grain of salt..  :)

            I also commend you for putting together an airplane that's
    running
            well.  I admire the accomplishment.


            Regards,

            Matt-

        Matt,
        I do have a glycol-air and an oil-air exchanger, but also an
    oil-glycol
        exchanger.  I don't see where removing the oil-glycol exchanger
    is going
        to improve the time I have to get on the ground should the
    glycol system
        spring a leak.  I may explore the possibility of building a
    dedicated
        exit duct for the oil-air exchanger though... in my spare time.
     If that
        works out, then I'll consider removing the oil-glycol exchanger.

        Mark S.

        I am really interested in why it is not working better. If you don't
        mind,
        next time you are out there, please record the number of fins per
        inch and the
        tube spacing. Also if you have a water manometer measure the
    pressure
        on the face of the oil cooler at speed. Use the porous foam hot
    glued to
        the end of the sense tube trick. You have my cooling book.

        Here is a chart of dynamic pressure verses speed. The pressure
    should be
        .3 to .4 of this number in the center of the core. If it is higher
        or lower
        there could be something wrong with the duct or the porosity of the
        oil cooler.

        In other words at 120 MPH dynamic pressure is 6.9 inches of water.
        The oil cooler face should be in the ball park of 2 to 2.8 inches of
        water.
        The higher the number the less the porosity of the oil cooler.
    If it is
        blocking the air flow through the core excessively it should be much
        higher
        than 2.8 inches.

        If it is lower than 2 inches you may have a leak in the duct or the
        duct may
        be improperly shaped.  You can do the same thing to the glycol rad
        and compare
        the two numbers. It would also be helpful to measure the pressure
        behind the core in the cowl as well.

        You would not happen to have any data like this on the oil cooler
        would you?

        My brain is kind of fried. Pardon the pun. Perhaps perhaps Bill
        Schertz can tell
        us where we want to be on the 3 rotor oil BTU rejection.

        Paul Lamar


    Paul,

    Won't the delta-P of the oil cooler be affected by the properties of the
    glycol exchanger and its duct?  If the glycol portion has especially low
    drag, I think the pressure inside the cowl will be relatively high (low
    delta-P across glycol exchanger), making it look like there's something
    wrong with the oil exchanger/duct.

    I guess if you check the pressure on the front side of the glycol
    exchanger, and in-cowl pressure, and compare all to ambient, you should
    have a pretty good picture of where the air wants to go.

    The inlet duct on the oil-air exchanger looks pretty good (geometry,
    shape).  If it leaked air, that would lower the glycol-air exchanger
    efficiency (that doesn't appear to be the issue) by raising the in-cowl
    pressure.  So, it seems like the oil-air exchanger might not be well
    matched to the glycol-air exchanger - when feeding a common outlet
    chamber.  If this is the case, the only fix I can think of is to arrange
    for an isolated outlet from the oil-air exchanger.  You could also block
    a portion of the outlet of the glycol-air exchanger, but that seems so
    wrong..  :)

    Mark, is your cowl in final paint?  I think it would be pretty easy to
    cut louvers aft of the oil-air exchanger, build a small outlet plenum
    and connect it to the outlet of the oil-air exchanger with large
    diameter scat tube.  Maybe it would look something like this:

    http://www.cs-ent.ca/6578o.jpg

    If it doesn't buy you anything, you wouldn't have spent much on it, and
    they'd be easy to cover over later (assuming you aren't in final paint).


    Regards,

    Matt-

    Best to put a small flap on there to keep the oil temp up
    at high altitude cruise. Reduces the GPH.

    --
    Paul Lamar ...No rotor no motor.



Sure..  I was just trying to come up with a cheap proof of concept.  A
cowl flap would be ideal.  Could even be controlled by a picaxe or maybe
simple a sealed bellows..

Matt-

VW thermostat. BTW it sucks air through the oil cooler when wide open.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.