Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/26/2008, 3:31 PM
To: AARotary Engine




                   Mark,

                   So you're not interested in the cooling redundancy that
       Paul has
                   suggested as a good idea - using oil-air and glycol-air
               exchangers at
                   the same time?  I still think that would be the
       direction I'd
               go.  In
                   fact, I'd make that a requirement, as I think it's
   something
               that could
                   make for a more favorable outcome should the
   airplane suffer
           from a
                   single component failure..

                   Maybe it's just anecdotal, but the vaunted P-51 Mustang
       has a
               separate
                   oil-air cooler, as I believe do the other Merlin powered
           aircraft
                   (Spitfires, Hurricanes, etc).  I think the P-40 (Allison
               powered) was
                   the same way.

                   The Mustang had an induction air to glycol supercharger
               intercooler, but
                   this ran with a separate cooling loop from the engine -
       and had
               its own
                   coolant pump and air-glycol exchanger.  This allowed
       putting the
                   intercooler where the
   directness/compactness/packaging is
               important.  It
                   wouldn't be practical to have a duct feeding an air-air
           intercooler
                   between the stages of the supercharger (on a Merlin).

                   Please keep in mind, I don't have a rotary powered
   airplane,
           nor a
                   liquid cooled airplane, nor even an airplane I built
       myself, so
               take my
                   ideas with a grain of salt..  :)

                   I also commend you for putting together an airplane
   that's
           running
                   well.  I admire the accomplishment.


                   Regards,

                   Matt-

               Matt,
               I do have a glycol-air and an oil-air exchanger, but also an
           oil-glycol
               exchanger.  I don't see where removing the oil-glycol
   exchanger
           is going
               to improve the time I have to get on the ground should the
           glycol system
               spring a leak.  I may explore the possibility of building a
           dedicated
               exit duct for the oil-air exchanger though... in my
   spare time.
            If that
               works out, then I'll consider removing the oil-glycol
   exchanger.

               Mark S.

               I am really interested in why it is not working better. If
       you don't
               mind,
               next time you are out there, please record the number of
       fins per
               inch and the
               tube spacing. Also if you have a water manometer measure the
           pressure
               on the face of the oil cooler at speed. Use the porous
   foam hot
           glued to
               the end of the sense tube trick. You have my cooling book.

               Here is a chart of dynamic pressure verses speed. The
   pressure
           should be
               .3 to .4 of this number in the center of the core. If it is
       higher
               or lower
               there could be something wrong with the duct or the porosity
       of the
               oil cooler.

               In other words at 120 MPH dynamic pressure is 6.9 inches of
       water.
               The oil cooler face should be in the ball park of 2 to 2.8
       inches of
               water.
               The higher the number the less the porosity of the oil
   cooler.
           If it is
               blocking the air flow through the core excessively it should
       be much
               higher
               than 2.8 inches.

               If it is lower than 2 inches you may have a leak in the duct
       or the
               duct may
               be improperly shaped.  You can do the same thing to the
       glycol rad
               and compare
               the two numbers. It would also be helpful to measure the
       pressure
               behind the core in the cowl as well.

               You would not happen to have any data like this on the oil
       cooler
               would you?

               My brain is kind of fried. Pardon the pun. Perhaps
   perhaps Bill
               Schertz can tell
               us where we want to be on the 3 rotor oil BTU rejection.

               Paul Lamar


           Paul,

           Won't the delta-P of the oil cooler be affected by the
       properties of the
           glycol exchanger and its duct?  If the glycol portion has
       especially low
           drag, I think the pressure inside the cowl will be relatively
       high (low
           delta-P across glycol exchanger), making it look like there's
       something
           wrong with the oil exchanger/duct.

           I guess if you check the pressure on the front side of the
   glycol
           exchanger, and in-cowl pressure, and compare all to ambient, you
       should
           have a pretty good picture of where the air wants to go.

           The inlet duct on the oil-air exchanger looks pretty good
   (geometry,
           shape).  If it leaked air, that would lower the glycol-air
   exchanger
           efficiency (that doesn't appear to be the issue) by raising the
       in-cowl
           pressure.  So, it seems like the oil-air exchanger might not
   be well
           matched to the glycol-air exchanger - when feeding a common
   outlet
           chamber.  If this is the case, the only fix I can think of is to
       arrange
           for an isolated outlet from the oil-air exchanger.  You could
       also block
           a portion of the outlet of the glycol-air exchanger, but that
       seems so
           wrong..  :)

           Mark, is your cowl in final paint?  I think it would be pretty
       easy to
           cut louvers aft of the oil-air exchanger, build a small outlet
       plenum
           and connect it to the outlet of the oil-air exchanger with large
           diameter scat tube.  Maybe it would look something like this:

           http://www.cs-ent.ca/6578o.jpg

           If it doesn't buy you anything, you wouldn't have spent much on
       it, and
           they'd be easy to cover over later (assuming you aren't in final
       paint).


           Regards,

           Matt-

           Best to put a small flap on there to keep the oil temp up
           at high altitude cruise. Reduces the GPH.

           --
           Paul Lamar ...No rotor no motor.



       Sure..  I was just trying to come up with a cheap proof of
   concept.  A
       cowl flap would be ideal.  Could even be controlled by a picaxe
   or maybe
       simple a sealed bellows..

       Matt-

       VW thermostat. BTW it sucks air through the oil cooler when wide
   open.

       Paul Lamar

   Yes, a/c is still in primer.  I'll see what I can do on this.  I'm
   pretty sure Lancair sells fiberglass gills that I could bond onto
   the lower cowl.  That's just what I wanted... more fiberglass work.

   Mark S.

   Make some measurements first and see if it is not something else
   such as an air leak in the input duct. The less porous the core the more
   important the input duct air leaks.

   Use thin wood ply door skins from the Home Depot to make the duct.
   Then cover
   them with glass. Quick and easy.

   As far as I know three people have been affected by coolant leaks. Two
   tried to turn back to the runway and crashed and one landed on the
   freeway.
   Non fatal crashes.

   When water turns to steam it expands something like 6000 times as I
   recall.
   What happens next is the pressure cap over pressure valve pops off
   and the steam pumps the remaining coolant overboard in seconds.
   Not something you want to fool around with.

   Use a cowl flap Mark.

   It will enhance the flow through the oil core during take off and
   climb out.

   Aero drag matters not on climb out. Much of the HP just goes to lift
   the weight of the airplane. 2500 pounds at 1000 feet per minute is
   is 2,500,000 ft pounds per minute. Dividing by 33,000 foot pounds per
   minute which is one HP equals 75 HP just to lift the weight of the
   aircraft
   alone not counting aero drag. If it is 1500 FPM it becomes 112.5 HP.
   The induced
   aero drag also increases due to the higher wing lift coefficient
   required.

   I know you know most of this as you have my cooling book so this is
   primarily
   for the new guys.

   Paul Lamar ...No rotor no motor.

Do the cowl skins have any core (nomex/foam)?  If not, I'd be tempted to
make a guess at where the outlet goes, and cut three sides of the
outlet, leaving the front edge attached.  Then wedge something in the
hole (a section of 2x4 or slightly thicker, wrapped in duct tape),
lifting the trailing edge of the flap outward.   Make a couple of layups
on the outside along the tapered edges of the scoop.  Allow to cure.
Remove the 2x4.  Add reinforcing layups to the inside.  Make a
connection for each end of the SCAT tube out of foam and glass...

Might look like this when done:

http://www.eagle1aviation.net/images/planes/1983%20Cessna%20210%20P/n4695a6.JPG

http://www.eagle1aviation.net/images/planes/1983%20Cessna%20210%20P/copyDSC00014.jpg



Matt-


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.