Subject: Oil to water heat exchanger data
From: Rotary Engine
Date: 2/27/2008, 3:25 PM
To: AARotary Engine


 Matt,
 Yes, the oil cooler is 3/8" thicker than the glycol
 exchanger. Also,
 maybe more significant, is that the fin count is much higher for
 the oil
 cooler, resulting in higher drag/pressure drop across it. I had
 considered adding a dedicated exit duct for the oil cooler, but
 didn't
 want to pay the drag penalty. That's when I decided to try the
 oil-to-water exchanger. The beauty with that solution is that
 it didn't
 cost me any additional cooling drag. I feel that if I could
 fit a
 slightly larger glycol exchanger in place of what I'm running
 now, that
 I could eliminate the oil/air exchanger altogether. I even flew
 with
 50% of the oil/air exchanger blocked off. It was pretty close
 with the
 current glycol exchanger, but not quite enough to fly in Texas
 in the
 summertime. So, I left the oil/air exchanger in place and don't
 have
 any more cooling problems. That's a real good feeling.

 Mark S.

 Mark,

 So you're not interested in the cooling redundancy that Paul has
 suggested as a good idea - using oil-air and glycol-air
 exchangers at
 the same time? I still think that would be the direction I'd
 go. In
 fact, I'd make that a requirement, as I think it's something
 that could
 make for a more favorable outcome should the airplane suffer from a
 single component failure..

 Maybe it's just anecdotal, but the vaunted P-51 Mustang has a
 separate
 oil-air cooler, as I believe do the other Merlin powered aircraft
 (Spitfires, Hurricanes, etc). I think the P-40 (Allison
 powered) was
 the same way.

 The Mustang had an induction air to glycol supercharger
 intercooler, but
 this ran with a separate cooling loop from the engine - and had
 its own
 coolant pump and air-glycol exchanger. This allowed putting the
 intercooler where the directness/compactness/packaging is
 important. It
 wouldn't be practical to have a duct feeding an air-air intercooler
 between the stages of the supercharger (on a Merlin).

 Please keep in mind, I don't have a rotary powered airplane, nor a
 liquid cooled airplane, nor even an airplane I built myself, so
 take my
 ideas with a grain of salt.. :)

 I also commend you for putting together an airplane that's running
 well. I admire the accomplishment.

 Regards,

 Matt-

 Matt,
 I do have a glycol-air and an oil-air exchanger, but also an oil-glycol
 exchanger. I don't see where removing the oil-glycol exchanger is going
 to improve the time I have to get on the ground should the glycol system
 spring a leak. I may explore the possibility of building a dedicated
 exit duct for the oil-air exchanger though... in my spare time. If that
 works out, then I'll consider removing the oil-glycol exchanger.

 Mark S.

Mark,

I'm not necessarily proposing that you remove the oil-glycol exchanger.
I just got the impression you were moving towards removing the oil-air
cooler if you could get the temps where you wanted them without it.. I
believe you said, "My only regret is that there isn't enough excess
cooling capacity that would allow me to remove the oil/air exchanger
completely."

Having both the oil-air and oil-glycol exchangers doesn't bother me.

Going without an oil-air exchanger bothers me. If you lose a bunch of
glycol you won't be directly cooling the metal in the engine, _nor_ will
you be cooling the oil that keeps the bearings and rotors happy. If you
have an oil-air exchanger, losing glycol supply doesn't directly impact
your ability to supply cool oil to the bearings and rotors, and so I
think that means the engine will run longer.


Regards,

Matt-

What's with the Glycol/air cooler nomenclature? It is WATER gents. Water
is the best cooling medium there is for heat transfer. The only reason
we use
glycol at all is to bump up the boiling point. If you have an adaquate
system,
that is pressurized to prevent boilover at altitude You need only a
lubricity additive.
Car racers frequently use only a lubricty additive and rust preventitive
in distilled water.
If you plane is hangared in the midwest, I can see glycol as it is
normally used in cars
as a anti-freeze agent, but never more than 50-50. Why lose heat
transfer capability
when our biggest problem is having radiators big enough? Just wondering.
Bill Jepson


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.