Subject: Opps I just invented something again IMPORTANT
From: Rotary Engine
Date: 2/28/2008, 9:48 AM
To: AARotary Engine


 >>      A manually controlled over pressure valve. When your airplane
 >>      starts spewing steam disable the valve and pump in cold
 >>      cooling water from an emergency reservoir supply until you get
 >>      it back on the ground. If you don't disable the valve you have to
 >>      pump it in at over 30 psi.
 >>      --
 >>      Paul Lamar ...No rotor no motor.
 >>
 >>
 >>
 >> Emergency spray bars - mist onto the rad inlet - would work great on
 >> Mark's layout since it would then blow any remaining water over the
 >> entire engine.  Cool the system, lower the tendency to boil.  How much
 >> flow do you need?  A windshield washer pump probably isn't enough.
 >> Maybe the domestic water pump from a travel trailer?  How about a
 >> pre-pressurized tank, or a CO2 cartridge which would pressurize the
 >> emergency tank.  How much water to haul?  1 gallon?  2?
 >>
 >>
 >> Matt-
 >>
 >> Evap water sucks down a lot of heat. Called the heat of vaporization
 >> as I recall. It don't take much.
 >> Paul Lamar ...No rotor no motor.
 >
 >
 >
 >> Paul,
 >> Use a 50/50 mix of methanol and water for spray. Better evap provides
 >> even
 >> more cooling. On the yak we run water spray bars on the oil cooler
 >> and run a
 >> 15 minute race at max power with the oil cowl doors closed. We use
 >> about 3
 >> quarts per minute, but we are cooling a 1600 horse power radial. You
 >> need a
 >> pump with a little bit of pressure so the water is a good mist coming
 >> out of
 >> the spray bar. The spray bar is nothing but a 3/8 stainless tube with
 >> .020"
 >> holes drilled in it. Our pump is an RV water supply pump for semi
 >> trucks as
 >> we are 24v. 12v ones are very cheap, made of plastic so they are light.
 >> Trick it to put it on an arm switch and have a coolant temperature
 >> switch
 >> turn on the pump and alert the pilot. You want to slow down the problem
 >> before you boil over to give you some air time to get down.
 >> Larry
 >
 >
 >
 >> Translates to .375 quarts per minute at 200 HP. At that rate a gallon
 >> (8 pounds)
 >> will buy about ten minutes. Pretty good unless you are out in the middle
 >> of nowhere. 200 MPH is 3.33 miles per minute or 33 miles in ten minutes.
 >> I think a 3 gallon tank (24 pounds) would not be out of the question.
 >> Almost 100 miles.
 > >
 >> Maybe a little bit of both. Make up water AND spray bar.
 >> --
 > > Paul Lamar
 >
 >
 > -----------------------------------------------------------
 >
 > Same idea as emergency core cooling in a Nuclear Power plant :-)
 >
 > Bill Schertz
 > KIS Cruiser #4045
 > N343BS (reserved)
 >
 > Wow! Cool! I did not know that.
 >
 >
 > --------------------------------------------------------------
 > VERY IMPORTANT:
 >
 >
 > BTW Bill, how do you convert BTU to Horse Power.
 >
 > If I use http://www.onlineconversion.com/energy.htm
 >
 > They 1 000 Btu = 0.393 014 802 horsepower hour
 >
 > Are BTU based on minutes so that is really .393 X 60 = 25.58 HP?
 >
 > I am trying to get a handle on the size and capacity of this oil cooler.
 >
 > This is the ONLY oil cooler I have good and complete data on.
 > Both air side and oil side.

  > Paul Lamar

 Paul,
 A BTU is a measure of energy.  Power would be BTU per unit of time.  1
 BTU  =  778 ft-lb

 So, 1 BTU/hr  =  778 ft-lb/hr  =12.97 ft-lb/min  =  3.93 E -4 horsepower

 Inverting this we get:   2545 BTU/hr  =  1.0 hp

 Aubrey

 Hummm you mean if I apply a torque on a stationary bolt for a period of time
 that is energy? How did I miss this in 72 years :) I am not saying
 you are wrong. Far from it. I totally believe you. I must have skipped that
 physics/thermo class. Obviously this is a huge gap in my thermo self education.

 There is no doubt my body would be burning calories.
 If you stood up for a period of time you would be burning calories.

 I thought it had to be rotating to get HP.

 So a BTU is a torque! Wow.

 What is the HP that this oil cooler is dissipating
 when it says 400 BTU's/min? We need about 50 HP for a 200 HP
 rotary.

 Now I am changing the subject to turbo compounding.
 Here is another hypothetical situation. If the 1700 F exhaust gases
 were not moving what would be the BTU? Would it depend on on how long they stayed
 at 1700 F? Would it be a function of the volume of the container?

 I am just thinking out loud here.
 Then the kinetic energy in the exhaust is only the mass of the gas moving at
 some speed? The heat of the gas has nothing to do directly with the kinetic
 energy. The application of heat of course increases the kinetic energy
 of the gas as it expands the gas. The gas expansion in an open ended pipe causes an
 increase in the kinetic energy as the expanded gas speeds up trying to get out.

 Is that an accurate description of what is happening?



 Paul Lamar ...No rotor no motor.


Paul,

The units for work (energy) and for torque are mathematically the same,
the product of force and distance.  But, the distance is measured
differently for the two.  Work occurs when a force is moved through a
distance and the distance is measured in the direction of the force.
Whereas, with torque, the distance is measured perpendicular to the
direction of the force.  Many years ago I had a physics instructor who
insisted that the units of torque should be written as "lb-ft" and the
units of energy should be written as "ft-lb".  This scheme is OK until
you have metric units.....who has ever encountered a
"meter-newton"....it just sounds strange!


If you push on something and it does not move, then no mechanical work
is done even though you may become tired and hungry from your muscles
converting chemical energy to force.  In the case of applying torque to
a bolt, no work is done unless the bolt turns.  If it turns, then your
force on the wrench handle would move in a circular path and the work
done would be the product of  distance along that circular path times
your force.


The "mechanical equivalent of  heat" is the conversion between
mechanical energy and thermal energy that in English units is

1.0  BTU  =  778 ft-lb.

Thinking about the engine exhaust gases, there would be several
components to the total energy:  pressure, mass&velocity, thermal
(BTU's), and some residual unburned chemical energy.  If the gases were
stationary and at a temperature of 1700F, there would be thermal energy
that could be extracted by reducing the temperature of the gases:

heat energy  =  (mass) x (specific heat of gases) x (temperature change).

Of course, in the exhaust stream these different energies are
intertwined because the random molecular motion in the gases contributes
to the pressure.  Your description of the action of the gases is about
right.  There are many subtle details, but the bulk of the energy
available to drive a turbine is embedded in the mass & velocity (kinetic
energy) part of the exhaust stream.   As an example of  one detail, the
inconel  "post-combustor" that Mistral has developed is an important
contribution because it extracts heat from some unburned hydrocarbons
and probably increases the pressure and velocity up-steam of the
turbine.  Your intuitive sense of the separation of the heat energy of
the gas and its kinetic energy is a good point to make.  The heat energy
is caused by the random molecular motion and consequently has no
specific "direction" associated with it.  Therefore, the heat energy
affects pressure and temperature which in turn will change the bulk
motion and kinetic energy of the gases.

Aubrey Thompson

I think this is well put Aubrey. Thanks

The "Heat of unburned gas." is shown this 13B heat balance chart.
The RX8 engine designers claim the side exhaust port recycles
most of this heat energy.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.