Subject: subscribe newsletter--Beckham/Groelz Dyno
From: Rotary Engine
Date: 2/28/2008, 11:44 AM
To: AARotary Engine




This is a great thing you are doing Paul.  Sure hope the folks who
use your reference materials fully appreciate them.  It is just
outstanding. For the better part of fifteen years Everett and I
didn't have such a nice consolidation of references and other
information available.  Pretty much had to do it on our own out in
that bean field and in library's, letters, etc. in the pre-Google
era.

So to see you serve up to them so much information, well it is just
terrific what you are doing to help keep the spirit of rotary
aircraft engines going.  Still have most of our technical library and

a good portion of our technical files, dyno sheets and other
references including all of the photographs and transparencies taken
of all our projects.  The detailed photographs are helping a lot.
And we still have the aircraft engine dyno that we built to test
Lycoming and rotary engines (with test club).  Am finally able to
think about rotary issues again, ten years later. For a long time, it

was just too painful.  But good to get parts in hand and get going
again.  Hope to make some noise on the dyno later in the year.  Are
you healthy and happy?

Steve Beckham


Thanks for the complements Steve.  I try to do the best I can.
Fairly healthy and fairly happy for 72 :) If you would scan some of
those old photos I am sure our readers would love to see them. You
two guys were the real aircraft rotary engine pioneers. We got some
guys in the North West that would love to borrow that dyno.

Perry Mick is in McMinnville. You should stop in and visit.
He now has over 600 hours I think. Ken Welter near Portland also has
a bunch of hours in a rotary powered Coot. Lots of fun going flying
with Ken :)

Paul Lamar ...No rotor no motor.

Steve gave me a tour of his hangar and rotary stuff about a year ago.

I occasionally fly to Mulino for breakfast, and then fly over Steve's
house on the way back to McMinnville via the Willamette River. I don't

think he's spotted me yet though.

I don't do the low buzz thing so I'm usually 1000 feet AGL.

Perry
675 hours



Thanks Paul.  Perry is a very sharp guy.  Am very impressed by his work.
Don't have his email address.  If you correspond with him I need his
advice on building the ram "J" tubes out of carbon to save weight.  My
pea brain can't figure out how to do it correctly.  We have grass field
so he probably can't fly in.  But can meet him in Mulino for breakfast.
Regarding dyno--when we get the dyno up and running we would like to
offer it as a service to folks.  Should do a lot for flight safety and
getting us some good solid numbers.  When I can figure it all out again
and won't be embarrassed, you ought to come down when we are it up and
testing.


Steve Beckman

Hi Steve... When you get the Dyno running, I'd love to get my engine on
it some time.  13B T04... Would be nice to run it and get the EC2
working before I mount it on the plane... Also would help see some
numbers before making a prop selection.  I'm in Everett WA are you in
Oregon?

Mike C

Steve, is this the dyno?
-- 
Paul Lamar ...No rotor no motor.


Paul--
Dyno--regarding your question....that is indeed our dyno.  From a quick
glance at it, it appears the photo was taken with it stuck in storage with a
bunch of Suelze family stuff.  When I get the time, will dig out photos of
it with an engine (it may be a Lycoming) installed, sitting outside in the
sunshine on the slab next to the shop where we tested engines.  To get to
the point of helping other folks dyno their engines, it will a long time
time.

Before then, we need to weld up a fixture for the dyno to our one-off
RV-3 mount system on the current engine.  Phillip Groelz and I will do this
after the engine/reduction gear is assembled and installed in the airframe.
Then need to reevaluate exhaust, muffler configurations, cooling and other
airframe integration stuff.  After that we hope to be making some noise with
this engine.  As to making it available to others who have asked about that,
we want to do that.

But it will be a long time because before that, we have
get the engine sorted out, finish the myriad of airframe details (its on the
gear) and fully flight tested.  My guess is we'll want to take the engine
out at least once or twice during that phase and make some changes. So it
will be quite a while before we are able to work with folks to see if we can
test their engines.

Phillip will need to work with them to see if this is
realistically possible because of a lack of uniformity of engine mounting.
Ours is unique.  Due to the location of the test club shroud/inlet vanes,
the prop flange will have to always be in the same location so folks would
have to fabricate their adaptor to fit the master mount plate on the dyno.
Another major factor is where we operate the dyno.  Phillip and I live in an
airpark, so there are major noise factors to address.  My shop and hangars
are just about full of equipment and the airplanes, so my guess is we'll
probably have to build a place to do it in Phillip's large hangar down the
street.  We live about seven miles from Van's Aircraft in Aurora.  In the
years we tested engines we were out in Everett's beanfield in the boondocks
so noise back then was not a major problem (although I'm sure some of the
neighbors a couple of miles away would disagree).


The business was sold to
Brent and it is a long way down there from here.  And if we dyno there, it
would be a disruption for Brent.  And it would have to work with what Brent
has going on and folks would need to compensate him for the time and
trouble.  So makes sense to do it here. But doing it inside a hangar here
will create a lot of work r.e. noise abatement, ventilation, etc.  In
addition to all of the above, we have a propeller R&D project for the rotary
engine that is in the works as well.

It is based on the work Everett and I
did flight testing a modified Aeromatic propeller on the RV-4 in1997.  Very
few folks got to see the aircraft fly in this trim.  It is very lightweight
and we know it is reduction gear and rotor gear friendly.  We were putting
up some good numbers with the modified aeromatic even though we were far
beyond the operating range of the stock Aeromatic blade and adjustments.
Phillip has his fertile mind working on all that.  And he is an electrical
engineer.  So converting our prototype blade angle controller to electric
servo with cockpit control function is something we want to evaluate with
modern blades engineered for the rotary-specific installation. Bottom line,
with all these projects going it will be a while before we are much help to
folks with the dyno.  But eventually we want to do it.


*Photo requests--As to your request for various photos...at some point I'll
need someone to volunteer to archive these by period and subject.  My guess
is there are several hundreds of photos taken of all our rotary projects
from the years 1984-1997.  Too much other stuff in the way presently.


*Cooling--I saw the messages related to cooling.  Regarding the note
recommendingWater Wetter, we found that very effective to help reduce
nucleate boiling in the rotor housings. And straight water with this or
similiar agents and watersoluable oil was used and glycol never used unless
absolutely required in winter.  The straight water cools much better (you
probably have the comparative charts; if not I'll dig them out).  Earlier we
worked with Dow to obtain propinate and tested that (biodegradable as I
remember).  If forced to use glycol due to winter weather to prevent
freezing, the system was flushed and replaced with only water,water wetter
and w-sol. oil as soon as possible.


*Regarding the note about introducing water to cool the plug boss
area....that design feature was included in our last SuperLight prototype
test flown in the RV-3.  On that engine, we made a manifold with cold water
jets and it bolted to the housings when the power section was assembled.  It
also served as a stressed member for the engine to add rigidity because
creep distortion of the aluminum housings at high power settings was an
early problem when we started doing our own aluminum end housing castings.
It bolted to the top of the engine (that engine was indexed 90 degrees with
sparkplugs on top).  But as was the case with a lot of the other trick stuff
we did with that engine, the down side was increased parts count, complexity
and cost that jacked up the cost on a production version beyond the capacity
of the buyers.  The stuff worked very well but too damned complicated and
expensive for the market.

When I sold Powersport it was with the expressed
desire that this engine be donated to the EAA museum.  It was fully
assembled and ran perfectly when we took it out of Alan's RV-3 and included
with Powersport assets with the sale.  In that regard, if it would be
helpful, I have a large number of good quality photos of the engine
components, fully assembled and for comparison of size and features, it
sitting alongside our first conversion engine with the internal spur gear
reduction drive.  And many good photographs of it installed in the aircraft
as well.

*Kudos to the submitter for the Pete Law information on cooling.  Great
stuff.  He and Bruce set a very high bar in that area.

*My apologies to folks for not responding timely to emails.  Have a lot of
other stuff in the way presently.  Take care.

Steve Beckham


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.