Subject: Poor man's Hypobaric Chamber
From: Rotary Engine
Date: 3/4/2008, 9:19 AM
To: AAA Put this in the To box


Paul,

Do we have anyone on this newsletter with experience with engine testing
within a hypobaric chamber? I am curious to know how they work.
I believe the chambers would have to have a means of blowing in fresh air
while sucking the exhaust out at a greater rate than the input air to
keep
the chamber at partial vacuums.

With the Poor Mans hypobaric Chamber, PMHC, lets us say that our
purpose is
to only test how much the recovery turbine increases in power at higher
altitudes. We won't have to test heat exchangers and electronics
because we
are confident our over-designed systems will function well at high
altitudes.  Yea right:)  In any case the oil and water cooling is handled
remotely like on standard dyno set ups.

Background info:

A turbocompound engine must be  boosted for the recovery of energy to
occur.
Let us assume we want to test the traditionally turbocompounding method
first. In operation both a supercharger and blow down turbine are
connected
to the drive shaft albeit in different locations. The supercharger is
taking
energy from the drive shaft and the blow down turbine is putting that
loss
and some 'plus alpha' power back into the shaft. In other words there
is a
net gain. Sort of like 'compounded interest'

Testing:

First the supercharger.  Factory test data curves showing power
consumption
at different pressures and airflows can be confirmed by running the
supercharger connected to a large electric motor and confirming the
results.
By the putting a torque arm on the free-to-rotate blower, and running it
through a manifold simulating the manifold resistance, the compressor
becomes the load. Temp., pressure, and air flows are documented as well.
Running the intake through a hypobaric (partial vacuum) chamber of
lets say
a 10 cubic foot thick steel pipe with a control valve set on the
intake set
to maintain a certain partial vacuum might work I think.

Second the exhaust.


Now imagine the  exhaust pipe is connected to our test turbine and from
there into a  another pipe hypobaric chamber.  Connected to the outlet of
this pipe would be a blower which was reversed so as to suck. This
powerful
vacuum unit will be driven by the same supercharge 25kW 3phase
electric test
motor and interfaced with a vacuum sensor set to keep the exhaust
hypobaric
chamber at 14.95" of Hg if we were simulating 18,000 ft.  Running the
test
in winter would give us our low STP intake temperatures.

Let me back up and say that this testing would be done only after the
engine
is running stable and in the boosted conditions. Next the blowdown
turbine
needs to be connected to a dyno. After the output is confirmed from
different turbines we can connect the best candidate to the drive shaft.

So what are we testing here?  We can understand that at a given CFM of
air
input, MAP, and altitude, how much power the blowdown turbine is putting
out. We hold the altitude and vary the MAP and/or RPM and note the
results.
In short we know how the  turbine's will perform at increasing high
altitudes.

Now if the goal was to test a turbochargers at altitude than this system
would work as well. We replace the supercharger, with a turbo charger and
compressor, and either a flexible shaft from the compressor to the
dyno set
or the turbo exhaust to another blow down turbine and then dyno.

I would appreciate comment on any of these premises.


Sincerely


Doug in Japan

You could test at the top of Pikes Peak or mount Fuji.

Or you could rent Pratt & Whitney test chamber.

Paul Lamar

It was a surprise to me P & W doesn't care what happens post engine. Of
course our engine doesn't matter as much as theirs does about the
velocity entering the engine, but  T & P we also care about. The car
makers here all test their cars at Pike Peak, particularly the towing
ratings. Are there road up Mt Fuji ?

-dave

Dave,

There is a road up to the fifth station of Fuji at 2300 meters but none to
the top.  I believe they had to bring the weather station dome on top by
helicopter. Mt Fuji is rugged and very exposed. Winds can and often do
literally blow people off the mountain. I was lucky to climb it on an autumn
day devoid of both wind and people.

http://www.japan-guide.com/e/e6901.html

I will haul the  engine complete with cowlings, and heat exchangers inside
the fan drive wind tunnel dyno up to altitudes for the final testing, but
now I am at the a turbine sizing planning stage.

About simulating high altitude testing, I reasoned that the input mass of
gases and fuel is  equal to the exit mass of gases but the temperature of
the gases and the volume of gases increase.

I don't fully understand how the ICE test chambers work but I reasoned that
they must allow the exhaust gases, to expand completely and then pull them
out of the chamber  with engine heat using huge exhaust fans. Their biggest
inputs of energy to run the chamber then is in exhausting the chamber at a
faster rate than the air comes in as well as the cooling loads for providing
the make up air. It is hard to fathom the amount of energy that is needed to
test a  jet engine at a simulated 65,000 feet.

 I am now just concerned with testing the performance of one exhaust turbine
at at simulated altitude. Can we computer model turbine performance at
altitude? Perhaps if we had some  data from turbo makers but that is like
pulling teeth.

On the input side of our engine we test at a temperature equivalent to what
we know exists on a STP day at our test altitude.  We use nature as it is
expensive to create the large and constant volume of refrigerated air we
need. This means winter testing. Giving this matter some more thought, since
we already know the performance of our compressor at different altitudes we
can downgrade its performance by altering it to match the expected
performance at a given altitude. Perhaps we can choke the inlet and/or bleed
air after the compressor.  This takes care of the input side.

On the exhaust side I'm not sure.  We would have to make the exhaust think
it was exiting the pipe into a partial vacuum atmosphere. Could this be
accomplished before the gases are expanded by pulling a partial vacuum on a
tee junction out near the final end of the exhaust manifold?  High
temperature would be the challenge so we would run a turbocharger in reverse
via a electric motor.  Just upstream we would need a way to measure the
ambient pressure and a feedback loop to control either the  electric motor
inverter or a solonoid operated bleed valve. Our testing would be done in
the steady state manner because with such small pipes, high velocities, and
high temperatures, the challenge is daunting.


Ah well...  Back to the drawing board.


Doug in Japan.

Doug, contact Barber Nichols for turbines.
http://www.barber-nichols.com/email_us/
engineer@barber-nichols.com

Don't tell them I sent you.
Make like GM or Toyota.

Paul Lamar

The alloy will be very interesting to me $$$ will be the issue. The 3
examples below all look like low temperature turbines.

-dave


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.