Subject: Three pcs end housings?
From: Rotary Engine
Date: 3/7/2008, 9:45 AM
To: AAA Put this in the To box




Paul, I have been thinking about this for some time... I really like
your idea about the aluminum side housings with the steel inserts with
the "O" ring seals. Here's an idea:

What if the stock Mazda gaskets were used and a simple steel side plate
was used with an extra side gasket with  an aluminum side plate of said
thickness between the 2 center side steel plates and single end steel
plates was used ? Much simpler to cast and machine. What do you think ?
KISS :-) Seams like center and end aluminum castings plates could be
milled on a Bridgeport, save for the steel plates.

-dave

Makes them three piece instead of two? It would probably work but it is
a lot of water seals. A lot cheaper than a hollow end housing. Probably
also cheaper than a hypereutectic end housing as well.


---------------------------------------------------------------

If we aluminum brazed the back piece on I think it might work.
Larry could do this in a heart beat. P-ports only which would
vastly simplify things. Heck JB Weld might even work.
REAL easy to try.

The steel wear plate could be through hardened and nitrided or porous chrome
plated.

Paul Lamar ...No rotor no motor.

Paul,

Couple things:
I asked on an earlier email and didn't get a response. The Rotomax side
housing are det. coated aluminum. I assume that their rotor housings are
their design as well.

Question 1: Do they SIP or det. coat the rotor housing as well?

When we talk thermal expansion problems the easiest thing to do is have
a similar metal througout the entire engine to have a consistant growth
and shrinkage along with the corresponding induced stresses. Radial
expansions such as bore liners in pison engines, SIP inserts in stock
rotor housings, and expansion plugs for aerospace fluid passages are
very predicable in their growth and shrinkage which allows you to easily
control the room temp fit to reduce contact stresses.

I like the idea of a two piece side housing for its replaceablility as
well for someone like me who is interested in doing their own custom
side housings. The only worry I would have is since the insert isn't
part of the casting the thing will warp from the heat variation across
the surface and also because even though you have some sort of standoffs
under the surface, there is no clamping load to make it stay put.
This will cause variations in the clearance to the rotor I would imagine.

Question 2: How critical in the side clearance to the rotors?

The drawing you have is for the o-rings in the side housings while the
rx-8 has them switched to the rotor housings. Your drawing also shows
the coolant not being exposed to the backside of the metal insert. The
stock inner o-ring serves as a combustion rings as well as a coolant
retaining ring.

Question 3: How do you control the radial postioning of the insert if
you have an o-ring between the insert and the side housing?

Question 4: Wouldnt you want to press fit the insert into the side
housing much like a cylinder liner to close off the water passages and
use the clamping of the housings to axially compress that interface like
your pic shows and have the inner rotor housing seal on the axial face
of the insert instead of on the radial face?

I am not critizing your idea but just wondering how you get that to work
correctly with the thermal expansion and making sure things are
clearance correctly. I saw the pic of you buddies two piece he made for
the single rotor and wondered if the ring of bolt about the staionary
gear combined with the clamping of the rotor housing would be adequate
for the job.

The other thing is how do you get this to all work for a side port
intake and exhaust engine? I have my ideas but I figured I would hear
yours before chiming in.

Rob Woods

?1. I don't know. They are not saying.
?2. It is critical down to .001. I don't know the actual clearance number
    but it is probably in the shop manuals.
?3. We may use short studs welded to the wear surface that fit in holes.
?4. No press fit is needed as the rotor housing keeps the side housing
    wear insert in place.

Last question. The short answer is: you don't. It will only work with
a p-port intake and exhaust. The big advantage of this system is the wear
inserts and be replaced when worn.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.