>>> Jerry,
>>>
>>> As I mentioned on Paul's newsletter, the engine is:
>>>
>>> 1987
>>> 13B
>>> turbo block
>>> NA, (normally aspirated-no turbo)
>>> Application: Long-Eze
>>>
>>> But:
>>> Has a 12A front plate.
>>>
>>> The 12A front plate means that a MM pick-up point on the
>>> oil pan is not necessary and not desired.
>>>
>>> So I can not say that the oil pan Hayes sent to me is for the
>>> average Turbo block. It may not be-but it is supposed to fit
>>> the block they built for me.
>>>
>>> As I would like to purchase the S-beam and oil pan from you, perhaps
>>> you can take the measurements from the pan I will send, along with
>>> those
>>> from Paul's newsletter.
>>>
>>> So if you can send me your shipping address I will send the oil pan
>>> I have.
>>>
>>> Regards,
>>> Joe Graham
>>
>>
>>
>> Joe, as long as the oil pan matches your engine I can take a
>> pattern off for the new pan. You say it is supposed to fit your
>> block. Just curious, is there some reason you cannot check it out?
>>
>> Is the s-beam asymmetrical or symmetrical? What is the distance
>> between Barry mount centers? The Long Eze may be too narrow for a
>> full length beam which is 29" between centers and 31" overall. If you
>> don't have this info, Paul can come up with it. He could also
>> customize the pan shape for your application if that were required.
>> It is a good idea to plan the entire engine mount so that we don't
>> find out later that the pan interferes with a motor mount tube or the
>> S-beam sticks through the side of the cowl. :)
>>
>> I understand you want just the s-beam and oil pan and not the complete
>> engine mount. The price for the S-beam is $400.00 and the price for
>> the oil pan without rear bracket is $350.00. Regards, Jerry
>>
>> My address for shipping and mail is
>> 3790 S. 600 W.
>> Albion, IN 46701
>
> The Long-EZ firewall is only 16" wide. On this page are some screen
> captures of drawings that are to scale. Center to center on the Schertz
> beam is 14" on my drawing. Any wider and you will have funny bumps on
> the sides of your cowl.
> http://www.mickaircraft.com/LEZ13B/LEZ13B.htm
>
> Perry
>
>
> I always thought this space in the Long EZ was wasted. Hard to get to.
> The landing loads must go through the structure and then into the landing
> gear. Why not feed them direct and save the weight of the structure.
> It also gives a better vertical spread to the firewall hard points
> reducing the load on the said hard points. Joe Berki used a new
> hard point along side the landing gear bolt which works fine
> but it is not necessary. A 4130 U shaped bracket would work fine using
> the same bolt.
>
>
> Paul Lamar
I agree that would be best for new construction. I decided to draw up
more of a "bolt on" solution for all the EZs already flying.
I'm wondering why Joe Berki's engine is so far aft? Even with two
batteries in the nose, I would have to add a lot of lead in the nose to
for cg if mine was that far aft. Joe might have explained this before
but I forgot.
Perry
He has a Limo EZ which is longer I think.
------------------------------------
Here is a 3 view 3D.
Paul Lamar ...No rotor no motor.
Paul,
I'm sure there's enough safety factor there, but I wonder about the
load path between the upper and lower motor mounts.
With the stock firewall, there's a single plywood bulkhead to support
the fuselage sides when reacting the shear load of the engine weight.
With the steps, the load path is less clear to me.
I believe the stock landing gear is canted forward at the wheels to
improve the way drag loads are supported - when braking and when
taxiing over bumpy surfaces especially. A wheel hitting a bump tends
to cause the gear bow to flex open, reducing the reaction on the
attachments.
As you have it drawn, I think the torsional loads due to bumps and
braking are higher and might require stronger attachments..
Regards,
Matt-
I don't have it drawn accurately. The side panels and the aluminum angles
are left in place and they provide a lot of support. Joe Berki's
pictures show it better. Also the engine inertia loads are the main
loads fed into the landing gear even under braking so it needs less support.
I need to redraw the 3D's and put in those details.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.