Dear Mr. P. lamar,
I have for a long time been looking for a rotary engine - but have
failed to find exactly what I need.
I need about 500 - 600 HP with mechanical adjustable prop w/reverse.
I need the engine for an air boat project.
Will you help me?
Yours sincerely,
Arne Egidiussen
500 to 600 HP is no problem but reverse thrust and a gear box might be
proplems.
Contact Mazdatrix and have them build a 3 rotor turbo for you.
http://www.mazdatrix.com/
Another source for such and engine is:
http://www.racingbeat.com/
A third is:
http://www.xtremerotaries.com/
The web site appears to be down but call Croydon NSW Australia
information
and ask. I think the following are dealers for xtremerotaries.
Turbosmart Head Office PO Box 264, Croydon NSW 2132 Australia
Turbosmart USA 1185 Park Center Drive, Suite Q Vista, CA 92081, USA
http://www.rotaryeng.net/boatvideo.wmv
MT have an adjustable pitch prop but reverse
might be a problem. Call them and ask.
http://www.mt-propeller.com/en/entw/stceasa/pilatus.htm
There are two possibilities for gear boxes.
Mistral and build your own.
http://www.mistral-engines.com/
Paul Lamar ...No rotor no motor.
I looked at the mistral engines, and I see the 230 HP is only rated for
5 min and cruise is down to 180 or something. I thought the advantage to
rotary was they could turn faster with no drawbacks. Why are they
de-rating them so much. Is there a MAP on a rotary like a piston engine
where you need to keep the MAP and RPM within a range?
If one had a 2 rotor putting out 200 HP would the fuel burn be the same
as a 3 rotor putting out the same HP? In other words if you need 200 HP
at altitude are you better off with a 3 rotor or a 2 rotor turbo? better
yet a 2 rotor turbo compound?
I have a line on my new rotary S5 RX-7 NA though. I should know in about
a week if I can pick it up.
Dan
Mistral is being very conservative. The 2 rotor normally aspirated
HP rating is now 200 HP. They are certifying the engines so they won't be
able
to change anything unless they go through the entire very expensive
certification
process over again. Nobody going to run an aircraft engine flat out at sea
level
anyway for very long. After it is certified and they have 10,000 hours or
so flight
experience you will see higher ratings.
You can run any MAP and RPM combination on a rotary.
Paul Lamar ...No rotor no motor.
Dan,
I have spoken to Francois as to why he didn't consider the PP, he suggested
for longevity reasons - the harder you run any engine the shorter the TBO -
Mistral is looking at 3,000 hrs TBO. As we only use the high HP for take-off
and climb, I can't see that making the TBO shorter, but I'm not the expert.
I should imagine Turbo making the TBO shorter as well.
Design your motor around your power needs and weight on FWF restrictions ;
is my design philosophy. 160 -180hp NA ( side port), 200 on PP and 250 hp
on Turbo, is my guess, but Paul would have a better handle on those figures.
I only need 115 to 125 hp ( at max of 300 lb FWF), so that's what I'm
concentrating on. The two rotor is a little heavier at 340 lbs and has too
much hp ( for my immediate needs), so I go for the single at approx 270 lbs
(guesstimate) and maybe 125hp (with a bit of luck).
George (down under)
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.