Subject: Cooling sytem changes- Velocity 20B
From: Rotary Engine
Date: 4/23/2008, 9:48 PM
To: AAA Put this in the To box



     Brief background: the oil temp was getting too high on extended climb
-
     coolant temp was OK, but I knew the wing-root radiator was not doing
     much due to low air flow.

     Mods:  I installed an oil/water cooler in the return line from the
     in-cowl radiator, I re-did the scoop and the shape of the diffuser to
     the wing-root rad, and installed an in-line 170F thermostat in the
feed
     to that rad. A number of other small fixes; and converted from the
OMP
     injecting pan oil to using pre-mix.  I put Mobile 1 15-50 in the pan.

     First test, a ground run to check everything out find leaks, purge
air
     etc.  After that some power running on the ground. The oil temp was
no
     longer the limiting factor, and stayed closer to coolant temp as
     expected.  What wasn't expected is that overall cooling on the ground
     was significantly better.  The only explanation could be that the new
     scoop and diffuser are so much better, just sitting face into the
10-12
     kt breeze helped the cooling.


     First test flight: OAT 68.  Climbed to 3000' and orbit the field.
Temps
     stayed well below limits in climb, and at cruise conditions the oil
was
     165 and the coolant 140.  Too cool?  Not even up the 170 temp of the
#2
     rad.  I had drilled some small holes in the thermostat to give at
least
     some flow, apparently even that was too much.

     Second flight: Went east over the hills to the dessert where the temp
a
     Borrego Springs was 85.  I did a touch and go; then climbed at
1500-2000
     fpm from 800' up to 6000'.  Oil stayed below 210; coolant about 195.
     Cruising back the coolant temp again dropped to about 145.

      Is it not a good idea to run the coolant that low?  I can change
     out the
     thermostat and not drill holes in it.


     The oil cooler I installed is a MoCal Laminova. These had also been
sold
     by Aeroquip, but not any more. Not very high capacity, but very
compact
     and fits where I wanted to put it (on the firewall, below the
filters,
     where my HP3001 filters no longer fitJ).  (photos 1 & 2)  I had
wanted
     to use the Setrab TOC300, but they are not currently making those.

     On the re-do of the scoop and diffuser, I made a mold and formed a
unit
     the would fit inside of the previous cutout in the wing.  It is a
curved
     adaptation of the K&W coordinates, and includes provision for
bleeding a
     ¼" boundary layer to the top edge of the core.  (photos 3 & 4).  My
     previous flow measurements had indicated the BL was about ¼".
Whatever;
     it seems to be working very well.  Perhaps had I done that same
     treatment to the oil cooler scoop and diffuser I could have skipped
the
     complex task of installing the oil/water cooler.  Nah, don't even go
     there!

     Al

     Hi Al,

     Glad to see everything is working well.
     The Hornet guys at Ramona want me to go for a ride in the
     Rotamax powered LSA Hornet. I said I would drive down to Ramona
     if I could coordinate a ride with you on the same day.

     Can that be arranged?

     Matt at Hornet's phone number is
     619 417 8895
     web site is www.sporthornet.com <http://www.sporthornet.com/>


     Folks, here is a wonderful video of Al's beautiful 3 rotor powered
     airplane.

     http://www.rotaryeng.net/Velocity_Vignette.wmv

     -
     Paul Lamar ...No rotor no motor.

Al,

Thanks for giving us an update on your oil cooling problem.  So glad to
hear that it is now cooling.  I only wish you had made one change at a
time so we would know which "fix" actually provided the most benefit.

Mark S.


Paul and Al,

Very nice video. Was there discussion about your muffler design?  Very
quiet.

As a student pilot, I can confirm that beacons draw the eye to your
plane for increased safety.  Should this have been in the LSA rules?

Coolant temps may be on the low side now, especially for oil temps.  It
is best to get above the boiling point of water (220?) to reduce acid
production in the oil.  I also believe using synthetic oils is better.

Dan F


Hi Al
      How many ponies are you producing approx. in the climb out mode it
sounds like you've got a pretty good combination going, also prop
dia. thanks, ron>



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.