Subject: Source for P-Port Rotor Housings
From: Rotary Engine
Date: 4/23/2008, 9:55 AM
To: AAA Put this in the To box

Dan,
I have spoken to Francois as to why he didn't consider the PP, he suggested
for longevity reasons - the harder you run any engine the shorter the TBO -
Mistral is looking at 3,000 hrs TBO. As we only use the high HP for
take-off
and climb, I can't see that making the TBO shorter, but I'm not the expert.
I should imagine Turbo making the TBO shorter as well.

Design your motor around your power needs and weight on FWF restrictions ;
is my design philosophy. 160 -180hp NA ( side port), 200 on PP and 250 hp
on Turbo, is my guess, but Paul would have a better handle on those
figures.

I only need 115 to 125 hp ( at max of 300 lb FWF), so that's what I'm
concentrating on. The two rotor is a little heavier at 340 lbs and has too
much hp ( for my immediate needs), so I go for the single at approx 270 lbs
(guesstimate) and maybe 125hp (with a bit of luck).
George (down under)



   Unfortunately, I've been so busy at work for the last 6-7 months that
   I've had to delay my Turbo 20B project, but I'm now back in the saddle
   and ready to start sourcing parts. I've decided to definitely pursue
   the P-Port configuration, but I'm not willing to attempt making the
   P-Ports myself. What are my options for sourcing well make P-Port
   Housings? I can't buy direct from Mazda. Racing Beat has some, but I
   don't know which housings to buy for the 20B. They also list both Turbo
   and Non-turbo housings. If I buy turbo housings and later decide to
   change to NA, do I have to buy new housings? Whats the difference??
   Don

Larry Childs said he can make the holes in the rotor housings quickly.
You can ship him your rotor housings he can bore the holes on his NC
mill using a custom jig and send them back. You tig weld them in or
have somebody do it for you. It is real easy.

I am thinking of sourcing a bunch of 2 inch SS tubes from Larry made on his 5 axis NC mill
and selling them on here near cost for those that want them. The tubes are rather time
consuming to make by hand. I will do a batch and when those are sold out I will
pause for awhile and do another batch when the demand increase.

Our youtube video on How to P-Port the RX8 engine has been very popular judging
on the rate of hits we are getting. There must be dozens of P-port engines being
built for the racer market. We have had over 1000 hits so far.

http://www.youtube.com/watch?v=LkKw72dZ2yc


Paul Lamar



Not an expert, but it depends on how you turbocharge it. If you are
going to boost it you need to be at a lower compression. If all you want
to do is normalize it, you are good to go with standard compression
because all you are doing is maintaining standard pressure. I planned on
using a manual waste gate in my IO-470-F when I was going that route.
Basically you do not use the Turbo until you get to altitude, Then start
closing the waste gate until you get to the MAP you want. Once you
decide to come down all you do is open the waste gate back up.

Dan


All true.

Any rotor housings will work for a 3 rotor except RX8. Late 3rd gen turbo housing are best but
they will work normally aspirated as well. The Mazda mods to the late rotor housings are minor.

Rotors control the compression ratio.
If it is a real 3 rotor and not built up from 13B parts the rotors are already
low compression. P-ports are great for turbo's as they will generate the same power
with less boost. It also simplifies the intake manifold.

If you want to run it normally aspirated it would be a good idea to use high
compression 1989 to 1991 13B rotors. That will give you a fewer gallons per hour
fuel burn. This is a rather expensive mod to a 3 rotor  because these H.C. used rotors
are in rather short supply. However the racers are probably getting them from
Mazda Speed which is the competition parts department.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.