Subject: Source for P-Port Rotor Housings
From: Rotary Engine
Date: 4/25/2008, 11:21 AM
To: AAA Put this in the To box



  > Dear Mr. P. lamar,
  >
  > I have for a long time been looking for a rotary engine - but have
  > failed to find exactly what I need.
  >
  > I need about 500 - 600 HP with mechanical adjustable prop w/reverse.
  >
  > I need the engine for an air boat project.
  >
  > Will you help me?
  >
  > Yours sincerely,
  >
  > Arne Egidiussen
  >
  > 500 to 600 HP is no problem but reverse thrust and a gear box might
be > problems.
  >
  > Contact Mazdatrix and have them build a 3 rotor turbo for you.
  > http://www.mazdatrix.com/
  >
  > Another source for such and engine is:
  > http://www.racingbeat.com/
  >
  > A third is:
  > http://www.xtremerotaries.com/
  > The web site appears to be down but call Croydon NSW Australia >
information
  > and ask. I think the following are dealers for xtremerotaries.
  >
  > Turbosmart Head Office PO Box 264, Croydon NSW 2132 Australia
  > Turbosmart USA 1185 Park Center Drive, Suite Q Vista, CA 92081, USA
  > http://www.rotaryeng.net/boatvideo.wmv
  >
  > MT have an adjustable pitch prop but reverse
  > might be a problem. Call them and ask.
  >
  > http://www.mt-propeller.com/en/entw/stceasa/pilatus.htm
  >
  > There are two possibilities for gear boxes.
  > Mistral and build your own.
  >
  > http://www.mistral-engines.com/
  >
  > Paul Lamar ...No rotor no motor.
  >
  >
  >
  > I looked at the mistral engines, and I see the 230 HP is only rated
for
  > 5 min and cruise is down to 180 or something. I thought the advantage
to
  > rotary was they could turn faster with no drawbacks. Why are they
  > de-rating them so much. Is there a MAP on a rotary like a piston
engine
  > where you need to keep the MAP and RPM within a range?
  >
  > If one had a 2 rotor putting out 200 HP would the fuel burn be the
same
  > as a 3 rotor putting out the same HP? In other words if you need 200
HP
  > at altitude are you better off with a 3 rotor or a 2 rotor turbo?
better
  > yet a 2 rotor turbo compound?
  >
  > I have a line on my new rotary S5 RX-7 NA though. I should know in
about
  > a week if I can pick it up.
  >
  > Dan
  >
  > Mistral is being very conservative. The 2 rotor normally aspirated
  > HP rating is now 200 HP. They are certifying the engines so they
won't be > able
  > to change anything unless they go through the entire very expensive >
certification
  > process over again. Nobody going to run an aircraft engine flat out
at sea > level
  > anyway for very long. After it is certified and they have 10,000
hours or > so flight
  > experience you will see higher ratings.
  >
  > You can run any MAP and RPM combination on a rotary.
  >
  > Paul Lamar ...No rotor no motor.

Dan,
I have spoken to Francois as to why he didn't consider the PP, he
suggested
for longevity reasons - the harder you run any engine the shorter the
TBO -
Mistral is looking at 3,000 hrs TBO. As we only use the high HP for
take-off
and climb, I can't see that making the TBO shorter, but I'm not the
expert.
I should imagine Turbo making the TBO shorter as well.

Design your motor around your power needs and weight on FWF restrictions ;
is my design philosophy. 160 -180hp NA ( side port), 200 on PP and 250 hp
on Turbo, is my guess, but Paul would have a better handle on those
figures.

I only need 115 to 125 hp ( at max of 300 lb FWF), so that's what I'm
concentrating on. The two rotor is a little heavier at 340 lbs and has too
much hp ( for my immediate needs), so I go for the single at approx 270
lbs
(guesstimate) and maybe 125hp (with a bit of luck).
George (down under)


Unfortunately, I've been so busy at work for the last 6-7 months that
I've had to delay my Turbo 20B project, but I'm now back in the saddle
and ready to start sourcing parts.  I've decided to definitely pursue
the P-Port configuration, but I'm not willing to attempt making the
P-Ports myself.  What are my options for sourcing well make P-Port
Housings?  I can't buy direct from Mazda.  Racing Beat has some, but I
don't know which housings to buy for the 20B.  They also list both Turbo
and Non-turbo housings.  If I buy turbo housings and later decide to
change to NA, do I have to buy new housings?  Whats the difference??
Don

Larry Childs said he can make the holes in the rotor housings quickly.
You can ship him your rotor housings he can bore the holes on his NC
mill using a custom jig and send them back. You tig weld them in or
have somebody do it for you. It is real easy.

I am thinking of sourcing a bunch of 2 inch SS tubes from Larry made on
his 5 axis NC mill
and selling them on here near cost for those that want them. The tubes are
rather time
consuming to make by hand. I will do a batch and when those are sold out I
will
pause for awhile and do another batch when the demand increase.

Our youtube video on How to P-Port the RX8 engine has been very popular
judging
on the rate of hits we are getting. There must be dozens of P-port engines
being
built for the racer market. We have had over 1000 hits so far.

http://www.youtube.com/watch?v=LkKw72dZ2yc


Paul Lamar

Paul,
If you decided to make a run of tubes, I would be interested. Please keep us
posted.

Joe Berki
Limo EZ


Any day now.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.