> > Hi Brian,
> > Something didn't sound right about sandwiching ANYTHING between the
> > prop flange and the drive flange, so I went out to my workshop and
> > looked at my Hartzel props. Sure enough the spinner bulkhead is
> > attached
> > to the OD (outside diameter) of the prop flange. Its an elaborate
setup
> > but, the bottom line is there is DIRECT CONTACT of the prop
flange and
> > the drive flange, no bulkhead, no RTV, no aluminum disks, no carbon
> > fiber or fiberglass. I have 2 props --a 2 blade & a 3 blade--
both are
> > done the same. Hope this helps. Dave M
> >
> >
> > >Dave,
> >
> > >Would it be possible to send a photo?
> >
> >
> > >Thanks,
> >
> > >Brian Trubee
> >
> > Hi Brian,
> > Photo would not show much. Take a look at the attached sketch. It's
not
> > to scale but all the parts are there. If you need sizes or more info
> > just shout. Dave M
> >
> >
> > My Spitfire came with the Spinner and a front and rear flange.
Showing
> > the rear flange between the prop and prop hub, the front on front
of the
> > prop. Prop bolts holding all this together. Is this an improper
> > installation?
> >
> > Bob Mears
> >
> > The smaller three rotor torque pulse is a positive while the
additional
> > average torque is a negative. What is the back plate made out of? If
> > aluminum
> > you will probably be OK.
> >
> > Paul Lamar ...No rotor no motor.
> >
> > The Rotary Engine NewsLetter. Powered by Linux.
> > ACRE NL web site. http://www.rotaryeng.net
<http://www.rotaryeng.net/>
> > Youtube key word UTUBPLEASE
> > Copyright 1998-2008 All world wide rights reserved.
> >
> >
>
> If the prop is aluminum, the bolts can be torqued plenty for this to
work fine.
>
> This is really the normal spinner installation on all of the
> fixed-pitch Cessnas, Pipers, etc. A backplate (and sometimes a front
> plate) held in place by the prop mounting bolts. Usually with drive
> lugs splined through the flange - offering more bearing surface for
> the torque loads in the prop and spinner.
>
> The c/s props have spinner backplate mounting flanges that don't use
> the same fasteners as which hold the prop to the crankshaft - like
> Dave M depicted. I suspect part of the reason for this is that
> there's a high pressure oil connection made by attaching the prop to
> the crankshaft. Adding the spinner backplate to this stackup seems
> like you'd eventually get leaks at this connection.
>
>
> Regards,
>
> Matt-
>
Replying to my reply..
I have a spinner from this outfit on my 182. I notice that all of
their bulkheads (back plates) appear to be composite, so that's
probably okay..
http://www.tcbcomposite.com/parts2sm.htm
I imagine what makes this work is the area being crushed is relatively
large - lowering the peak pressure.
Compare the transverse compressive strength of carbon rod (idealized
composite, but in its weakest axis - what we're talking about here):
50MPa
http://www.goodfellow.com/csp/active/static/A/Carbon-Epoxy_Composite.HTML
To aluminum: ~270MPa for 2024
Matt-
What is that in psi Matt?
-- Paul Lamar ...No rotor no motor.
Ok guys unless I missed something doesn't the prop flange have drive
lugs, (cylinders),
that protrude into the bolt holes? Most, if not all of the drive torque
would be handled there.
The bolts are supposed to just be in tension, with low shear forces.
Bill Jepson
In theory yes. Usually there is enough slop to cause problems.
If it fits tight you are OK. The trouble with wood it absorbs
water and grows.... and shrinks.
Paul Lamar ...No rotor no motor.
Yes, even a well sealed wood prop changes thickness with the weather. A
few months ago Marc Zeitlin lost a wood propeller from his Cozy during a
cross-country flight. The airframe damage was minor and he was able to
make it to an airport and he landed safely. The incident stimulated
much discussion on the canard and Cozy oriented forums. The attached
article surfaced during those discussions. Although the examples
presented are for traditional all wood props, (ie: no bonded aluminum
backing plate like the Catto has) it is clear that the "proper" way to
drive a prop is via the friction between the drive hub and the prop.
Maintaining the proper pressure between the drive hub and the prop
requires frequent, perhaps weekly, checks of the prop bolt torque. An
idea that was suggested during the discussions was to use Belleville
washers on the prop bolts to maintain a relatively constant bolt tension
while the prop expands and contracts with the weather. Marc has done
this and it appears to be working well. Three or four washers per bolt
are required to get enough linear spring range.
If we assume that the 600psi bearing stress (4.14 MPa for Matt)
mentioned in the article is sufficient, then I would expect a
carbon/fiberglass composite spinner bulkhead to work well.
Aubrey Thompson
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.