Subject: Experimental rotary in my car?
From: Rotary Engine
Date: 5/16/2008, 4:26 PM
To: AAA Put this in the To box


Hello Paul,

I just picked up a 81 Toyota starlet that I am going to turn into a road
legal race car. I have already sourced a transmission and rear end for
what I am going to do but now it is time to pick and engine. The car
weighs 1700lbs now and with the upgrades will get to 2000lbs. I am
trying to make up my mind on the engine to use and I have narrowed it
down to a LSX, lexus V8 or a N/a or Turbo rotary. I am shooting for a
power level of 300hp with the option of getting up to 500 which the LSX
can do in its sleep and the lexus can make about 400-450. A boosted
rotary could do it as well but I am thinking a N/A rx-8 with p-port
intake would probably make me happy as well just for the novelty and
other chassis dynamcis reasons. If I have to go higher than I would have
to go 13B and boost. I am looking at a number of factors such as
cg,cost,weight,durability,etc. I am leaning toward a p-port intake rx-8
because I want to make a lemans style telescoping intake for testing for
my 4 rotor idea I have been working on. I figure I want to do it in the
long run so I might as well start a little smaller and pick up some data
to finalize ideas on the big one since things seem to scale pretty close
to 1:1 on these things. I have the following question to narrow this down.

1:  What is the true weight of an rx-8 N/A and 13b N/A engine? The only
real engineering reason to go with a rotary is is weight advantage but
people are swapping in lsx engines into turboed 2 rotor rx-7s and only
adding about 30lbs to the car.

2:  How much would it cost to make a set or rx-8 p-port intake housings
at this point assuming I already have a motor?

3:  How do you block off the existing side ports when you switch?

4:  I looked at your mazda matrix dyno sheets vs what I believe are dyno
sheets for a longer runner full p-port 13b engine. I am I correct that
assuming for trends that the side port exhaust really doens impact the
power that much? I know the runners were longer which should lead to
lower power numbers.

5: What is the idle quality of the rx-8 p-port intake? No difference?
Higher idle?

6: Is there any good place to get used rx-8 engines that you are aware of?

Rob Woods

What is an LSX engine?

The bare RX8 engine less all accessories and manifolds is 190 pounds about.
Turbo's add weight.

Contact Larry Childs on the RX8 p-port housings.
Larry Childs <larry@designitprototype.com>

You use JB Weld to block the side ports.

The idle quality is about the same as the old 13B.

I have no idea on where to get used RX8 engines. Wrecking yards I suspect
are the only option. Perhaps Japanese engine importers are another
possibility.

Paul Lamar ...No rotor no motor.



If I wanted a go-fast car based on a production vehicle, I would put the
RX-8 engine in a Series 1 Miata.

Steve Brazil

It's been done .

Clifton


LSx is the series of latest generation small block chevrolet..  It's
the one with deep skirts that extend well below the crank centerline.

http://en.wikipedia.org/wiki/GM_LS_engine

Rated for 505hp as an LS-7 in the Z06 vette.

http://www.superchevy.com/technical/engines_drivetrain/completebuilds_testing/0509sc_assembly/index.html

Not to be confused with the LSX (listed at the bottom of the above
wiki article).


Matt-


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.