Subject: Mistral Crash maybe an exhaust problem - cut & shut -
From: Rotary Engine
Date: 6/8/2008, 5:24 AM
To: AAA Put this in the To box


>        > A Piper Arrow powered by a prototype Mistral
>        > ( http://www.mistral-engines.com/ ) rotary aircraft
>        > engine
>
> crashed
>
>        > after the
>        > engine lost power following takeoff from Palatka
>        > Municipal-Lt.
>
> Kay
>
>        > Larkin
>
> I did the collapsed muffler deal at Sebring years back. The
> Flowmaster (big suitcase looking thing) had all of the baffles
> piled up against the rear outlet. The muffler swelled up like a
> giant pillow and the power dropped off to nearly nothing. It
> didn't hurt the engine at all and we raced at West Palm Beach the
> next weekend.
>
> Lynn E. Hanover
>
>
> Since you brought up the subject Lynn it is time to revisit the
> proper way of welding
> the exhaust pipes to the exhaust flange.
>
> The weld must be around the inside of the flange and not on the
> outside. Even better is to have a non welded ball joint where the
> pipe joins the flange
> like this early Steve Beckham and Everette Hatch Power Sport
> configuration.
> That allows the exhaust system to expand and contract without
> stressing the joint.
>
> http://www.rotaryeng.net/flange-welding.html
>
> ------------------------------------------------------------------
>------------------
>
> Well now we know it had something to do with the muffler.
> When I first saw these pictures I did not pay too much attention
> as I thought it was made from Inconel.
>
> On hindsight I can see several mistakes made by Mistral. Some of
> which may be moot
> if constructed from Inconel. It might work as is if constructed
> out of Inconel.
>
> First, was the two pipes were welded on the wrong side of the
> flange. http://www.rotaryeng.net/flange-welding.html
> We had a rotary powered Velocity crash because of this.
>
> Second, a lot of trouble went into building a slip joint into the
> two piece inner can
> and then the two clips were rosette welded to the outer can
> defeating the purpose
> of making the inner can two pieces. Also one EGT can be higher
> than the other so there
> will be distortions.
>
> I always tell people NOT to put ANYTHING into the inner can as it
> will melt
> for sure. Heck my C182 spit its guts out of the can on the ramp at
> Valdez and the EGT's
> are only 1400 F and not 1800 F. One of my pax saw it and freaked
> out. I said; "Not to worry we don't need that part." :)
>
> Tom Jordans Limo EZ back in 2003 had a similar muffler to this
> one. You could stand
> behind the prop and look directly into the can at full chat
> through the down pipe.
> The inner stuff was white hot... almost transparent. Only a matter
> of time for that
> to melt and be spit out through the prop. It could have hit me in
> the eye and
> blinded me. Stupid stunt.
>
> Since most people do not want to pay a $1,000 or $2,000 for an
> Inconel muffler
> make the hollow can out of .065 inch thick 321 SS and let it go at
> that. --
> Paul Lamar ...No rotor no motor.

Paul--Thank you for beating the drum regarding the unique demands of
rotary aircraft engine exhaust systems.
We cannot overemphasize the homework, diligence and precaution
required in this area to provide flight safety.

When Everett and I started our rotary aircraft engine dyno and
flight test program we had 70 combined years of engine and racing
experience--including some with rotary powered race cars--yet we
were totally unprepared for what we found with rotary aircraft
engine exhaust systems.

Based on that experience, we concluded the combined performance, size, and safety demands imposed on rotary aircraft exhaust
components are unique in the four-cycle world.  The rotary aircraft
engine demands a low back pressure system that is compact, light,
durable, with a pleasing exhaust note, will fit inside various
cowlings/airframes, and operate safety at sustained high output for
hours on end.  We know we can do one or more of these things.  But
to do them all....it is an order of magnitude.  Our ultimate success
with safe high performance rotary aircraft engines will depend on
it.  It is a work in progress.

Simply put, this is an issue that can kill you any number of ways
and none are pretty.

Due to the factors you have presented, the many factors involved in
rotary aircraft engine exhast systems are not simple.
We are all collectively on the learning curve.

It may be old news, but here are some of the basic things regarding
exhaust system design, construction and components we learned in our
12 year rotary aircraft engine program.

1. Traditional automotive components, designs, materials and
construction would fail.  They did not work due to a plethora of factors you have explained.

2.  Systems developed for reciprocating and rotating piston/Mazda
engine race cars, and reciprocating aircraft engines, were not
transferrable and were not usable for numerous reasons.  Even with
rotary engine race cars the duration of high engine output/exhaust
energy with the pedal down and and staying there is generally
measured in seconds down the straight and between curves.  Ours in
aircraft are measured in hours by comparison.  We don't lift our
foot for corners.

3. Even on dyno runs (these maxiumum output runs lasted minutes not
hours) we had top of the line mufflers puff up like a ballon and
eventually assume that appearance permanently--and crack. We
modified a top of the line Flowmaster for flight tests with a front
section and baffles of 600 series SS/Inconel.  Performance and sound
quality was excellent due to combination of volume, design,and low
back pressure. But it had too many flat sections and the rear
(unmodified portion standard) deteriorated in a relatively short
time and blew up like a baloon.

4.  Learned to avoid flat sections in all components due to
vibration and cracking. The obvious exception was the flange and we
found we didn't have to use Inconel for those (321 was ok).  But
Inconel or equivalent was required for pipe sections close to out of
the port and front section of the muffler sections.  SS 321 could be
made to work but requires a thicker, heavier pipe section that adds
weight.  Inconel just stronger and better in every way.  The Inconel
with the thinner wall has superior overall high temperature
performance--strength, creep, fatigue and temperature.

5. Learned to beware of cantilevered components and keep moment arms
short

6. Exhaust pipes joined to other pipes/ports without special
provision for expansion would always ultimately crack  The only way
we could make it work to weld a pipe directly to an exhaust flange
was to make it a stub pipe that was very short with bellows or slip
or swivel joint (swivel preferred but most difficult) incorporated
as close to, or as part of, the flange and port insert.  We did use
some Inconel bellows but really liked the simplicity, funtionality
and cost effectiveness of simple slip joints.

7. Anything we put inside a muffler would  be broken and pieces spit
out downstream eventually unless it was an open chamber muffler with
properly designed and constructed internal sections fully supported
with 600 series stainless (Inconel,etc) used in the front sections
directly exposed to the flame and pulse.

8. The use of Inconel and other  600 series stainless materials
assured nothing if other design factors was overlooked.  Early on we
experienced failures even with Inconel tubing  up to .100 wall

9. We learned never to assume that because it has worked for "x"
hours that it is an infinite life piece or assembly

10. In simple terms, we learned to visualize a violent percussive
supersonic blowtorch/hammer of 1600-1700 degrees turning metal
translucent coming out of the ports of the engine, pointed directly
at a plastic cowling, structure, wiring, fuel lines, and some cases
even propeller.

Regarding this last point, some year back I flew back to Kansas and
inspected a beautiful, newly-built Velocity RG with a rotary engine
and three-blade MT prop.  The workmanship and features of this
airframe were beautiful.  It was a stunner, capable of winning
Oshkosh.  It was built by a great guy and the work and expense that
had gone into it was clear.  It had not yet flown but ran well and
he was down to just fixing a few minor glitches before the first
flight.  Several things about the exhaust system made me very
nervous and told him so and why.  Later I heard it was lost on its
first flight due to exhaust system failure.  Looking at some of your
exhaust file photos it appears that it may be one of the examples
you use. Very sad.

Steve Beckham

They fixed it Steve and it is still flying.

Paul Lamar


Hi all - I am just thinking about the technique of cutting & welding
component's to move the resonant frequency away from where you don't
want it. IIRC the frequency moves up , and it does not have to be a
total cut either - I am thinking of the end - plates & flat baffles.
Also , maybe these can be slightly curved so they ain't a flat plate.

Fly & Build good -
-- 
Bryan In England



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.