Subject: book shelf 10 times stronger
From: Rotary Engine
Date: 6/12/2008, 7:05 PM
To: AAA Put this in the To box


     I just invented a cheap book shelf that is ten times stronger   and
     stiffer
     than a plain wood book shelf. It matters not if the 20 gage (.  020
  thick)
     steel sheet is glued to the 3/4 birch ply on the bottom or  the  top.

     Do you want to know how it works?
     Google neutral axis of beams.

     The neutral axis of the beam is moved towards the high   strength and
     high stiffness
     cheap 20 gage steel sheet.

     --
     Paul Lamar ...No rotor no motor.


  What kind of glue Paul?  And just sandpaper the metal
  surface?   Thanks,      Dave D.

  Construction adhesive in tube and applicator.
  No sanding. The shear stress apparently is minimal.

  Might make a good 1/2 inch thick Schertz beam if it will
  withstand the heat. You would need no spacers for the pan bolts
  or anything other than a hole for the Barry rubber bushings.
  I would use the thinest 4130 steel sheet on both sides of a 1/2   inch
  thick Oak board you can buy. 0.025" would be plenty thick enough.
  Probably need 300 F epoxy.

  I designed a "Modified" (now called "Late Model") space frame race
  car 30 years ago for
  Steve Smith Autosports using thin mild steel on both sides of 3/4
  plywood for
  the firewall. It was so stiff you could hang the brake pedals and
  brake cylinders
  off it with no reinforcements. Handy. Hundreds if not thousands   were
  built as
  Steve Smith sold plans for years and years.

  It would also make a good aircraft firewall too if you used  thin . 016"
  stainless steel on both side of 1/4 inch ply.

  The fabricator had a 44 Magnum long barrel revolver. He wanted to
  see what would happen if he fired a bullet at it point blank range.
  The purpose was to see if it would function as a light weight   clutch
  scatter shield.
  The bullet was captured in the firewall and did not completely
  penetrate.

  Verified the term "bullet prof" when applied to race cars :)

  --
  Paul Lamar ...No rotor no motor.



Paul,  But wouldn't one have to be cautious on compressing the  wood  when
attaching fixtures?
Very fascinating.
On the bookshelf one could use smaller dim than the wood by an inch  or
two maybe more, and not degrade the strength?  Dave D

Not really because the steel and a washer distributes the   compressive load
into the wood over a larger area. Oak can be used  for the Schertz   beam
and it has a very high compressive strength. Another advantage is the
beam can be band sawed to fit the oil pan and pick up a few more  bolts
on both sides.

Would be great for mounting the Rotamax as well.

Here are some 3D's

The big advantage for shelves is you can use a longer span without
the books causing sagging. That cuts the cost of more verticals.
-- 
Paul Lamar ...No rotor no motor.

I like this!!  It would take a significant amount of weight  out of
the beam.   And it would be no harder to make.   Could the metal be
aluminum?   Jerry


4130 only Jerry. Aluminum would be too flexible and would conduct
more heat. Give it the pick up truck test.
-- 
Paul Lamar ...No rotor no motor.

I'm interested researching high temp adhesives for this application.
What is the max temp the beam would be exposed to?    Jerry

Hard to say. If you get a muffler too close to it it could exceed
300 F which is about the highest epoxy temperature you can get. The engine probably
runs 200 F. Not such a good idea when you think about the temperatures
it could be exposed too. Lets stay with what we got. We know it works.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.