Subject: Higher power for your rotary.
From: Rotary Engine
Date: 6/16/2008, 9:04 AM
To: AAA Put this in the To box


   Formula One 1 engine technology is pressing the current power
   to weight ratio advantage of the rotary.
   Currently a NA 3 rotor P-port running about 11,000 RPM is
   generating about 550 HP as a guess. Bare block weight is 260 pounds.
   Back in the 1980's the NA P-port two rotor had no problem
   generating about 300 HP at about 9000 RPM while weighing
   200 pounds (bare block weight) with cast iron end and center housings.
   Aluminum irons could cut that weight to about 150 pounds.
   On the other hand formula one tech has approached that
   power to weight ratio advantage. Of course rotaries
   are outlawed in Formula 1 but that is neither here nor there
   for this discussion. They should be allowed to reap the advantages
   of the huge amounts of engine development money generated in Formula 1

   http://www.pureluckdesign.com/ferrari/f1engine/

   "A time traveler from 50 years ago would find today's Formula 1 cars
   radically different, but would be equally surprised at the relative
   lack of change in engine technology. Turbochargers have come and
   gone and there hasn't been a switch to two-stroke or rotary, scotch
   yoke engines - let alone to gas turbines or something not even invented
   in 1950. The good old four-stroke internal combustion engine powered the
   very first Grand Prix car in 1906 and lives on in a form instantly
   recognizable by any time-traveling engineers from 1950."

   "The power output of the four-stroke internal combustion engine
   is a function of the torque seen at its flywheel and the speed
   at which that flywheel spins."

   "The increase in performance of the current 3.0-liter engines
   is purely a function of faster flywheel (crankshaft) speed."

   "To attain 800hp, a current Fl engine must turn in the region
   of 17,000rpm, which means its peak power bmep roughly equals
   that of the 1967 DFV."

   "Since 1998, Ilmor has manufactured pistons from an aluminum-beryllium
   alloy, thereby reducing their weight by a third, possibly more,
   and gaining enhanced thermal conductivity."

   End of quotes.

   How can we get the speed of the rotary up to 17,000 or 19,000
   RPM? If you can't beat them join them in the switch to
   aluminum-beryllium alloy (ABA) for the rotor. That is the key.
   http://www.reade.com/Products/Alloys/aluminum_beryllium_alloy_al_be.html

   ABA density is .076 pounds per cubic inch while that of cast iron
   is .3 pounds per cubic inch. The current nine pound rotor is cast iron.

   .076/.3 is .25 so an ABA rotor would weigh about 2.28 pounds or less
   as ABA is stronger than cast iron.

   The limit to the RPM in a rotary is the centrifugal load on
   the rotor bearing.

   Load = mV^2/r
   r drops out for equal size engines.

   V is proportional to RPM so 11,000 squared is 121 million.
   m is proportional to weight so 9# X 121,000,000 is 1089,000,000.
   So 1089 million is our load target.

   Load = 1,089,000,000 = 9# X RPM1^2 = 2.28# X RPM2^2

   or 1089,000,000 / 2.28 = RPM2^2 = 544500000


   So 1089/2.28 = RPM^2 = 477,663,1578
   The new RPM = the square root of 477,663,1578 or 23,334 RPM!!!

   HP is proportional to RPM so my guess is
   23,334/11,000 X 550 or 1,167 HP for a NA P-port 3 rotor!!!!!

   Same rotor bearing load.

   Of course the rotary would still be a lot cheaper than
   a Formula 1 engine as there are not a lot of the other
   high tech expensive  parts such as titanium rods and pneumatic valves.

   Turbo compound would be easier as now we are really getting
   up to turbine RPM speeds.

   Sure we don't need 1000 HP in our passenger cars but the point is
   you can make the engine much much smaller hybrid or otherwise and
   still get enough HP.

   That drastically cuts the size and weight of the car improving the MPG.

   Bob W please check my arithmetic.

   -
   Paul Lamar ...No rotor no motor.



Paul,  Won't cooling become the big obstacle with much higher RPM?
Possibly a redesign of exhaust port area?
Dave D

Cooling is proportional to HP. So yes cooling will have to be increased.
Perhaps it may be necessary to use both side exhaust ports
and P-exhaust ports doubling the area. Of course is anyone really
going to build a NA 1000 HP engine? I don't think so. What will probably
happen is a half or third size rotary with the same power. Turbo 3 rotors
are pushing 1500 HP.

Do you have a set of SCCA rules for that class of racing you can send me?
I have a few ideas for you that will reduce the drag and lift.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.