Formula One 1 engine technology is pressing the current power
to weight ratio advantage of the rotary.
Currently a NA 3 rotor P-port running about 11,000 RPM is
generating about 550 HP as a guess. Bare block weight is 260 pounds.
Back in the 1980's the NA P-port two rotor had no problem
generating about 300 HP at about 9000 RPM while weighing
200 pounds (bare block weight) with cast iron end and center housings.
Aluminum irons could cut that weight to about 150 pounds.
On the other hand formula one tech has approached that
power to weight ratio advantage. Of course rotaries
are outlawed in Formula 1 but that is neither here nor there
for this discussion. They should be allowed to reap the advantages
of the huge amounts of engine development money generated in Formula 1
http://www.pureluckdesign.com/ferrari/f1engine/
"A time traveler from 50 years ago would find today's Formula 1 cars
radically different, but would be equally surprised at the relative
lack of change in engine technology. Turbochargers have come and
gone and there hasn't been a switch to two-stroke or rotary, scotch
yoke engines - let alone to gas turbines or something not even invented
in 1950. The good old four-stroke internal combustion engine powered the
very first Grand Prix car in 1906 and lives on in a form instantly
recognizable by any time-traveling engineers from 1950."
"The power output of the four-stroke internal combustion engine
is a function of the torque seen at its flywheel and the speed
at which that flywheel spins."
"The increase in performance of the current 3.0-liter engines
is purely a function of faster flywheel (crankshaft) speed."
"To attain 800hp, a current Fl engine must turn in the region
of 17,000rpm, which means its peak power bmep roughly equals
that of the 1967 DFV."
"Since 1998, Ilmor has manufactured pistons from an aluminum-beryllium
alloy, thereby reducing their weight by a third, possibly more,
and gaining enhanced thermal conductivity."
End of quotes.
How can we get the speed of the rotary up to 17,000 or 19,000
RPM? If you can't beat them join them in the switch to
aluminum-beryllium alloy (ABA) for the rotor. That is the key.
http://www.reade.com/Products/Alloys/aluminum_beryllium_alloy_al_be.html
ABA density is .076 pounds per cubic inch while that of cast iron
is .3 pounds per cubic inch. The current nine pound rotor is cast iron.
.076/.3 is .25 so an ABA rotor would weigh about 2.28 pounds or less
as ABA is stronger than cast iron.
The limit to the RPM in a rotary is the centrifugal load on
the rotor bearing.
Load = mV^2/r
r drops out for equal size engines.
V is proportional to RPM so 11,000 squared is 121 million.
m is proportional to weight so 9# X 121,000,000 is 1089,000,000.
So 1089 million is our load target.
Load = 1,089,000,000 = 9# X RPM1^2 = 2.28# X RPM2^2
or 1089,000,000 / 2.28 = RPM2^2 = 544500000
So 1089/2.28 = RPM^2 = 477,663,1578
The new RPM = the square root of 477,663,1578 or 23,334 RPM!!!
HP is proportional to RPM so my guess is
23,334/11,000 X 550 or 1,167 HP for a NA P-port 3 rotor!!!!!
Same rotor bearing load.
Of course the rotary would still be a lot cheaper than
a Formula 1 engine as there are not a lot of the other
high tech expensive parts such as titanium rods and pneumatic valves.
Turbo compound would be easier as now we are really getting
up to turbine RPM speeds.
Sure we don't need 1000 HP in our passenger cars but the point is
you can make the engine much much smaller hybrid or otherwise and
still get enough HP.
That drastically cuts the size and weight of the car improving the MPG.
Bob W please check my arithmetic.
-
Paul Lamar ...No rotor no motor.
Good thinking.
Just looking at the math, since Force is M * acc, and with constants
removed F = M *n^2
If mass M1 is .25 M, reduced by a factor of 4 , n1^2 is allowed to go up
by a factor of 4 for equal force.
So n = sqrt of n^2 or n1 = sqrt of 4 = 2n,
If the first n with cast iron rotor is 11,000 rpm the new n1 with BAB
rotors is 22,000 rpm, roughly. (depending on the exact weight ratio)
Wonder what BAB will cost compared to 'standard' Al alloys, or compared
to the presently used cast iron rotors.
The thermal stability of cast iron is higher than that of Al-alloys. ABA
would have to be closer to cast iron to take the beating in the Rotary
engine.
Rolf
Thanks Rolf.
I think you mean ABA instead of BAB? Aluminum-Bryllium Alloy
is closer to cast iron than aluminum.
Paul Lamar
Paul,
I have used Be-38AL alloy that is now sold as AlBeMet162 by BrushWellman.
The following link will give you very good material properties data.
http://www.berylliumproducts.com/Attributes.aspx?id=AlBeMet162
The main issue would be wear in the apex seal and corner seal areas (would
need a hardened insert). The side clearances would also have to be looser,
as this grows more than cast iron. On the up side, the coefficient of heat
transfer is very good. This would make charge cooling more effective for
those engines, and oil cooling more effective on mazda style.
And boy would these be expensive parts.....
Although.... it tig welds very nicely, so a multi part rotor could be made
and welded together.....
Anyone with a big pot of money? :)
Larry
Agreed and all good observations. Not something we can do but certainly
within what Mazda can do. Thanks also for the fabrication tips.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.