Subject: Higher power for your rotary. Maybe a breakthrough???
From: Rotary Engine
Date: 6/19/2008, 6:50 AM
To: AAA Put this in the To box


       What amazes me the Brits were using WW II era RR58 aluminum
       alloy pistons
       up until about 1997 for engines turning 14,000 RPM.
       With oil spray for cooling. Earlier Formula 1 turbo charged
       pistons used an oil gallery built into the piston
       for cooling. Oil pressure was sent up the (probably titanium)
       connecting
       rod, through the piston pin and into the oil gallery.

       The same approach could be used in the rotary.
       Instead of squirting the oil up inside the aluminum alloy rotor
       the cooling oil could be fed through the rotor bearing
       into a matrix of oil galleries inside the rotor.

       X2020-T6 would have been a better choice than RR58 IMHO.


       Paul Lamar ...No rotor no motor.


   Paul,
   Good idea and is already being successfully done up to a point.

   As the single rotor has difficulty having sufficient space for an
   oil jet
   like the two rotor, some are drilling a hole in the centre of the
   rotor to
   take the rotor cooling oil directly from the bearing supply hole of the
   e-shaft.
   There could be 3 holes drilled one facing the centre of each rotor
   face, if
   necessary, keeping the hole size small so that it doesn't starve the
   bearing
   lubrication.

   Can't see why this system couldn't be used in a lightened rotor.
   George (down under)

   +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++


   This relatively recent development is REAL promising.


   Quote:
   NASA Marshall Space Flight Center - Huntsville, AL
   Revision Date: 01/18/2007
   Information : High Strength Aluminum Casting Alloy for High
   Temperature Applications

   A hypereutectic alloy such as A390 is a conventional aluminum alloy
   used to make pistons
   in U.S. automotive engines. This alloy has adequate strength, is
   easily cast, and is
   low in cost.

   However, a typical alloy such as A390 aluminum alloy used in the
   design has inadequate
   tensile strength in the required 500° to 600° F temperature range.

   In 1995, Marshall Space Flight Center's (MSFC's) metallurgists began
   working with Ford
   under a Space Act Agreement to develop a new, castable aluminum
   alloy that had a 30%
   improvement in tensile strength during operation in the required
   temperature range.
   The result was an aluminum-silicon alloy that meets or exceeds all
   original automotive
   criteria. Figure 3-3 shows a 600° F, tensile strength comparison of
   available aluminum
   alloys against the NASA alloy. The projected cost of the
   aluminum-silicon alloy is 95¢
    per pound versus 87¢ per pound for A390. Since less of the new
   alloy material is required
   due to its higher strength, the cost per piston is expected to be
   comparable. MSFC has currently
   filed a patent on the aluminum-silicon alloy, and negotiations are
   ongoing with Ford and
   other U.S. automobile manufacturers regarding its use.

   End of quote.

   No details yet of the percentages of different materials in the alloy.
   600 F will work fine for a rotor with internal oil cooling and steel
   inserts
   for apex seal slots. The rotor might weigh about half of the current
   9 pound
   iron rotor so RPM might be 1.50 higher or about 16,500 RPM. HP might
   be as much
   as 480 for a NA P-port two rotor and 720 HP for a three rotor. It
   will be
   a lot cheaper than BeAl alloy.

   Paul Lamar ...No rotor no motor.


Paul,  Would coating the rotor faces with ceramic make this NASA
alum-silicon work?    Dave D

Perhaps but it would have to be very thick. I would say
a minimum of .032" thick. It would also have to be very tough
as if it came off it would destroy the rotor housings.
The track record so far is very bad. I have seen rotor housings
that have been destroyed by failed ceramic coated rotors.
Not pretty. A fitted SS sheet mechanically fastened would be more reliable.
This has been done with heavy duty pistons.

Perhaps the entire high silicon aluminum rotor encased in thin SS sheet tig welded
along the sides as cost is no object on this type of racing engine.
The sheet could be formed in a press.
The apex seal slots could be incorporated in SS. SS has low thermal conductivity
which in theory improves the combustion efficiency as it contains more heat.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.