Today I flew from San Diego to Brownville Texas to attend a formation
flying clinic. After 6 hours of WOT flight I was descending through
5000' (down from 15.5k) an just a few miles from the airport when I had
a sudden and sickening drop in manifold pressure. The engine was still
running fine, and I had plenty of altitude to make the runway, so I
continued on debating weather or not to flip the turbo oil shutoff
switch. I had grown to respect this turbo so much that I finally
decided that I had just blown out a fitting somewhere in the intake
system downstream of the turbo. I even continued on to a low pass for
show rather than just landing. When I eventually had time to take off
the cowl I was disappointed to find that all the fitting were in place
and that the compressor wheel turns only with significant resistance.
So the turbo is dead, and I am out of the formation clinic and will have
to decide tomorrow about flying home with a dead turbo. Will maybe be
able to take a look in the hot side and see what I see.
This turbo was the TO4 hybrid with a fixed wide open waste gate. It had
130 hrs of mostly hard duty. Sigh.
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
Sorry to hear that Dave. You are our main turbo development man.
Let me review the configuration. Larger TO4 compressor wheel adapted to
stock
late 2nd gen turbo. Is that correct? Was the stock turbine trimmed?
Is this the one with the enlarged exducer?
Turbo life is now up from two hours to 130 hours to look at the positive
side.
IMHO We still need a turbo tach.
---------------------------------------------------------------
Dave, I wager when the turbine cracked is when you got to 15,500 feet for
awhile. I think that is when the turbo RPM exceeded its obvious red line.
The higher you go the less back pressure on the turbine and the higher
the turbine RPM. I know you know this but we have a lot of new readers.
I also think what we need is a simple diverter valve ahead of the turbo
that
positively diverts the exhaust gas to an auxiliary exhaust pipe bypassing
the turbo completely.
Conventional waste gates don't do this. They merely open a hole in the
exhaust
manifold in the hopes this will reduce the pressure across the turbine and
cause it to slow down. Obviously it is not working well enough.
This diverter valve can be operated by a signal from the turbo tachometer
limiting the turbine RPM. There is not a lot we can do about exhaust gas
temperature but we can limit turbine RPM. Turbines fail from a combination
of RPM and temperature. Limit one or the other and the turbine will live.
This chart from Caterpillar graphs the situation. The red dotted line on
the
right is the RPM limit. The red dotted line on the left is the turbine
inlet temperature. One must stay between the red lines. The black curves
can be considered as HP lines as this is a diesel. More fuel more HP.
Do we need a 3D?
BTW Dave this R&D you are doing IMHO will become invaluable when the
time comes
to build a turbo compound rotary. I thank you in advance. The world will
owe you a debt of gratitude.
--
Paul Lamar ...No rotor no motor.
Paul,
I had an idea that may help with the "heat" problem:
Could the turbocharger be mounted downstream from the exhaust exit,
allowing the hot exhaust to cool somewhat before it entered the
turbo...? Thinking more on it, could cooling fins be added to the
exhaust header, between the exhaust port and the downstream turbo, to
further cool the exhaust gasses...?
If the exhaust gasses were cooled below 2K degrees (perhaps more)
the impeller may survive high-speed spikes...
Jack Beale
Sure the P47 had it in the aft fuselage.
http://rwebs.net/avhistory/history/p-47.htm
Paul Lamar
Sorry about your turbo failure it reinforces my thoughts on remote setups.
I've looked at several Corvette configurations and the temperatures
are much lower, no data yet but it will be interesting to follow the
discussions.
Paradocs on AF1
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.