Subject: Another Turbo Bites the dust
From: Rotary Engine
Date: 6/22/2008, 7:24 AM
To: AAA Put this in the To box




        Today I flew from San Diego to Brownville Texas to attend a
        formation
        flying clinic.  After 6 hours of WOT flight I was descending through
        5000' (down from 15.5k) an just a few miles from the airport
        when I had
        a sudden and sickening drop in manifold pressure.   The engine
        was still
        running fine, and I had plenty of altitude to make the runway, so I
        continued on debating weather or not to flip the turbo oil shutoff
        switch.  I had grown to respect this turbo so much that I finally
        decided that I had just blown out a fitting somewhere in the intake
        system downstream of the turbo.  I even continued on to a low
        pass for
        show rather than just landing.  When I eventually had time to
        take off
        the cowl I was disappointed to find that all the fitting were in
        place
        and that the compressor wheel turns only with significant
        resistance.

        So the turbo is dead, and I am out of the formation clinic and
        will have
        to decide tomorrow about flying home with a dead turbo.  Will
        maybe be
        able to take a look in the hot side and see what I see.

        This turbo was the TO4 hybrid with a fixed wide open waste gate.
         It had
        130 hrs of mostly hard duty.  Sigh.

        --
        David Leonard

        Turbo Rotary RV-6 N4VY
        http://N4VY.RotaryRoster.net
        http://RotaryRoster.net

        Sorry to hear that Dave. You are our main turbo development man.

        Let me review the configuration. Larger TO4 compressor wheel
        adapted to stock
        late 2nd gen turbo. Is that correct? Was the stock turbine trimmed?
        Is this the one with the enlarged exducer?

        Turbo life is now up from two hours to 130 hours to look at the
        positive side.

        IMHO We still need a turbo tach.

        ---------------------------------------------------------------

        Dave, I wager when the turbine cracked is when you got to 15,500
        feet for
        awhile. I think that is when the turbo RPM exceeded its obvious
        red line.
        The higher you go the less back pressure on the turbine and the
        higher
        the turbine RPM. I know you know this but we have a lot of new
        readers.

        I also think what we need is a  simple diverter valve ahead of
        the turbo that
        positively diverts the exhaust gas to  an auxiliary exhaust pipe
        bypassing
        the turbo completely.

        Conventional waste gates don't do this. They merely open a hole
        in the exhaust
        manifold in the hopes this will reduce the pressure across the
        turbine and
        cause it to slow down. Obviously it is not working well enough.

        This diverter valve can be operated by a signal from the turbo
        tachometer
        limiting the turbine RPM. There is not a lot we can do about
        exhaust gas
        temperature but we can limit turbine RPM. Turbines fail from a
        combination
        of RPM and temperature. Limit one or the other and the turbine
        will live.

        This chart from Caterpillar graphs the situation. The red dotted
        line on the
        right is the RPM limit. The red dotted line on the left is the
        turbine
        inlet temperature. One must stay between the red lines. The
        black curves
        can be considered as HP lines as this is a diesel. More fuel
        more HP.

        Do we need a 3D?

        BTW Dave this R&D you are doing IMHO will become invaluable when
        the time comes
        to build a turbo compound rotary. I thank you in advance. The
        world will
        owe you a debt of gratitude.
        --
        Paul Lamar ...No rotor no motor

    .
    Paul,
    You snatched the words right out of my mouth and it's something I
    suggested
    some time ago. At the time you requested a drawing and II supplied a
    rough
    one, but to be fair all things must be tried and I would suggest
    they have
    been pretty well tried by Dave to this point.

    I wonder how Mistral are doing theirs. Regardless restricting the
    heat and
    flow is the most obvious way to assure survivability of the Turbo IMHO.
    George (down under)

    I am rapidly coming to the conclusion that the problem lies with the
    RPM and not the turbine temps. 1050 C is 1900 F.

    The turbine temps are about half the EGT temps.


    Paul Lamar ...No rotor no motor.


Paul,
This may sound overly simplistic, but if too much heat is the culprit,
why not move the turbo further away from the exhaust ports?  Seems to me
that this would dissipate a good portion of the excessive heat and also
the excess flow as the exhaust  will contract as it cools.  I vaguely
recall seeing a picture of someone's turbo installation where the turbo
is located downstream of a tangential muffler (possibly Tom Parkes'
20B).  Tom doesn't post often, but last I heard, he wasn't having any
turbo problems.

Mark S.
67.7 hrs (no turbo)

I now don't think heat is the main problem given the recent Borg Warner
FEA's on the subject. The turbine is operating at half the EGT's temps.
See the attached charts of temperature.

I think the reason Tom's is working better is its an aircraft turbo.
Obviously aircraft turbo's are designed differently and for  a constant speed engine
and moderate to high  engine HP. That to me means a modest HP turbine with a
large compressor. There is so much kinetic energy in the rotary engine exhaust it
is easy to over speed the car turbo charger. Brief over speeds don't hurt it.
Long term over speeds will destroy it.

The aircraft turbo has the effect of keeping the turbo charger RPM within limits. Dave
had his car turbo charger modified along those lines. A larger compressor
was added.

"The compressor is a 60-1 and the turbine is a TO4 clipped to fit in
the stock housing.  With the wastgate open [it] can only make about 30" MAP
at that altitude, but I can't use it all because my prop is not big
enough.  I hit 6700 engine RPM but I didn't feel comfortable staying
there."  [2.17:1 gear box].

BNR Supercars
393 Coupland Rd.
Branchville, AL 35120
 (205) 640-1193
BNRsupercars@yahoo.com / AIM: BNRsupercars


I think it was  a large step in the right direction. With a spacer
between the stock 2nd gen turbo and stock  manifold a yet larger compressor
could be added.

Unfortunately what was also done, as I recall, was the exducer was opened
out which was a small step in the wrong direction.

"The turbine housing is opened up tremendously therefore decreasing backpressure."

You want to keep some back pressure on the turbine to keep the turbine HP and RPM down.

Most car turbocharger tuner guys don't understand the problems adapting car
turbo chargers to aircraft use.

It is all in Hugh MacInnes book "Turbochargers" but you have to
read between the lines sometimes and think about the implications.

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.