Today I flew from San Diego to Brownville Texas to attend a
formation
flying clinic. After 6 hours of WOT flight I was descending
through
5000' (down from 15.5k) an just a few miles from the airport
when I had
a sudden and sickening drop in manifold pressure. The engine
was still
running fine, and I had plenty of altitude to make the runway, so I
continued on debating weather or not to flip the turbo oil shutoff
switch. I had grown to respect this turbo so much that I finally
decided that I had just blown out a fitting somewhere in the intake
system downstream of the turbo. I even continued on to a low
pass for
show rather than just landing. When I eventually had time to
take off
the cowl I was disappointed to find that all the fitting were in
place
and that the compressor wheel turns only with significant
resistance.
So the turbo is dead, and I am out of the formation clinic and
will have
to decide tomorrow about flying home with a dead turbo. Will
maybe be
able to take a look in the hot side and see what I see.
This turbo was the TO4 hybrid with a fixed wide open waste gate.
It had
130 hrs of mostly hard duty. Sigh.
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
Sorry to hear that Dave. You are our main turbo development man.
Let me review the configuration. Larger TO4 compressor wheel
adapted to stock
late 2nd gen turbo. Is that correct? Was the stock turbine trimmed?
Is this the one with the enlarged exducer?
Turbo life is now up from two hours to 130 hours to look at the
positive side.
IMHO We still need a turbo tach.
---------------------------------------------------------------
Dave, I wager when the turbine cracked is when you got to 15,500
feet for
awhile. I think that is when the turbo RPM exceeded its obvious
red line.
The higher you go the less back pressure on the turbine and the
higher
the turbine RPM. I know you know this but we have a lot of new
readers.
I also think what we need is a simple diverter valve ahead of
the turbo that
positively diverts the exhaust gas to an auxiliary exhaust pipe
bypassing
the turbo completely.
Conventional waste gates don't do this. They merely open a hole
in the exhaust
manifold in the hopes this will reduce the pressure across the
turbine and
cause it to slow down. Obviously it is not working well enough.
This diverter valve can be operated by a signal from the turbo
tachometer
limiting the turbine RPM. There is not a lot we can do about
exhaust gas
temperature but we can limit turbine RPM. Turbines fail from a
combination
of RPM and temperature. Limit one or the other and the turbine
will live.
This chart from Caterpillar graphs the situation. The red dotted
line on the
right is the RPM limit. The red dotted line on the left is the
turbine
inlet temperature. One must stay between the red lines. The
black curves
can be considered as HP lines as this is a diesel. More fuel
more HP.
Do we need a 3D?
BTW Dave this R&D you are doing IMHO will become invaluable when
the time comes
to build a turbo compound rotary. I thank you in advance. The
world will
owe you a debt of gratitude.
--
Paul Lamar ...No rotor no motor
.
Paul,
You snatched the words right out of my mouth and it's something I
suggested
some time ago. At the time you requested a drawing and II supplied a
rough
one, but to be fair all things must be tried and I would suggest
they have
been pretty well tried by Dave to this point.
I wonder how Mistral are doing theirs. Regardless restricting the
heat and
flow is the most obvious way to assure survivability of the Turbo IMHO.
George (down under)
I am rapidly coming to the conclusion that the problem lies with the
RPM and not the turbine temps. 1050 C is 1900 F.
The turbine temps are about half the EGT temps.
Paul Lamar ...No rotor no motor.
Paul,
This may sound overly simplistic, but if too much heat is the culprit,
why not move the turbo further away from the exhaust ports? Seems to me
that this would dissipate a good portion of the excessive heat and also
the excess flow as the exhaust will contract as it cools. I vaguely
recall seeing a picture of someone's turbo installation where the turbo
is located downstream of a tangential muffler (possibly Tom Parkes'
20B). Tom doesn't post often, but last I heard, he wasn't having any
turbo problems.
Mark S.
67.7 hrs (no turbo)
I now don't think heat is the main problem given the recent Borg Warner
FEA's on the subject. The turbine is operating at half the EGT's temps.
See the attached charts of temperature.
I think the reason Tom's is working better is its an aircraft turbo.
Obviously aircraft turbo's are designed differently and for a constant
speed engine
and moderate to high engine HP. That to me means a modest HP turbine with a
large compressor. There is so much kinetic energy in the rotary engine
exhaust it
is easy to over speed the car turbo charger. Brief over speeds don't
hurt it.
Long term over speeds will destroy it.
The aircraft turbo has the effect of keeping the turbo charger RPM
within limits. Dave
had his car turbo charger modified along those lines. A larger compressor
was added.
"The compressor is a 60-1 and the turbine is a TO4 clipped to fit in
the stock housing. With the wastgate open [it] can only make about 30" MAP
at that altitude, but I can't use it all because my prop is not big
enough. I hit 6700 engine RPM but I didn't feel comfortable staying
there." [2.17:1 gear box].
BNR Supercars
393 Coupland Rd.
Branchville, AL 35120
(205) 640-1193
BNRsupercars@yahoo.com <mailto:BNRsupercars@yahoo.com> / AIM: BNRsupercars
I think it was a large step in the right direction. With a spacer
between the stock 2nd gen turbo and stock manifold a yet larger compressor
could be added.
Unfortunately what was also done, as I recall, was the exducer was opened
out which was a small step in the wrong direction.
"The turbine housing is opened up tremendously therefore decreasing
backpressure."
You want to keep some back pressure on the turbine to keep the turbine
HP and RPM down.
Most car turbocharger tuner guys don't understand the problems adapting car
turbo chargers to aircraft use.
It is all in Hugh MacInnes book "Turbochargers" but you have to
read between the lines sometimes and think about the implications.
Paul Lamar
P,
Please indulge a question here:
Has anyone ever calculated the rpm at which an impeller fails...?
I'd think that it would be fairly easy to use engineering data to
calculate that value for several curves based on temperature.
Let's say that, at ambient temperature (room temp), the impeller has
to reach 250,000 rpm (calculated) before failure. We all believe that
as temperature rises, the strain is increased and the impeller will fail
sooner. Why not show a series of (calculated) curves, plotting stress
against strain (to failure) for a set of temperature curves near (900
deg to 1,400 deg) what we believe the operating temperature of the
turbocharger impeller....?
Jack Beale
Given the lack of information from turbo charger manufacturers on
HP of the turbines I don't think it is possible to calculate the RPM.
Perhaps I am wrong. One might figure the HP required to generate x amount
of compression and then go into the compressor map to determine
the RPM.
We still need a turbo tach. A turbo tach would also allow us
to determine the turbo charger RPM acceleration. We can then tell
where we are relative to compressor load.
BTW I just learned something about that subject watching the Formula 1 races.
Ferrari listens to and watches the Speed Channel and determines the rate of
acceleration of their competitor's cars by analyzing the on board sound of
the engines :)
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.