> > Today I flew from San Diego to Brownville Texas to attend a
> > formation
> > flying clinic. After 6 hours of WOT flight I was descending
> > through
> > 5000' (down from 15.5k) an just a few miles from the airport
> > when I had
> > a sudden and sickening drop in manifold pressure. The engine
> > was still
> > running fine, and I had plenty of altitude to make the runway, so I
> > continued on debating weather or not to flip the turbo oil shutoff
> > switch. I had grown to respect this turbo so much that I finally
> > decided that I had just blown out a fitting somewhere in the intake
> > system downstream of the turbo. I even continued on to a low
> > pass for
> > show rather than just landing. When I eventually had time to
> > take off
> > the cowl I was disappointed to find that all the fitting were in
> > place
> > and that the compressor wheel turns only with significant
> > resistance.
> >
> > So the turbo is dead, and I am out of the formation clinic and
> > will have
> > to decide tomorrow about flying home with a dead turbo. Will
> > maybe be
> > able to take a look in the hot side and see what I see.
> >
> > This turbo was the TO4 hybrid with a fixed wide open waste gate.
> > It had
> > 130 hrs of mostly hard duty. Sigh.
> >
> > --
> > David Leonard
> >
> > Turbo Rotary RV-6 N4VY
> >
http://N4VY.RotaryRoster.net
> >
http://RotaryRoster.net
> >
> > Sorry to hear that Dave. You are our main turbo development man.
> >
> > Let me review the configuration. Larger TO4 compressor wheel
> > adapted to stock
> > late 2nd gen turbo. Is that correct? Was the stock turbine trimmed?
> > Is this the one with the enlarged exducer?
> >
> > Turbo life is now up from two hours to 130 hours to look at the
> > positive side.
> >
> > IMHO We still need a turbo tach.
> >
> > ---------------------------------------------------------------
> >
> > Dave, I wager when the turbine cracked is when you got to 15,500
> > feet for
> > awhile. I think that is when the turbo RPM exceeded its obvious
> > red line.
> > The higher you go the less back pressure on the turbine and the
> > higher
> > the turbine RPM. I know you know this but we have a lot of new
> > readers.
> >
> > I also think what we need is a simple diverter valve ahead of
> > the turbo that
> > positively diverts the exhaust gas to an auxiliary exhaust pipe
> > bypassing
> > the turbo completely.
> >
> > Conventional waste gates don't do this. They merely open a hole
> > in the exhaust
> > manifold in the hopes this will reduce the pressure across the
> > turbine and
> > cause it to slow down. Obviously it is not working well enough.
> >
> > This diverter valve can be operated by a signal from the turbo
> > tachometer
> > limiting the turbine RPM. There is not a lot we can do about
> > exhaust gas
> > temperature but we can limit turbine RPM. Turbines fail from a
> > combination
> > of RPM and temperature. Limit one or the other and the turbine
> > will live.
> >
> > This chart from Caterpillar graphs the situation. The red dotted
> > line on the
> > right is the RPM limit. The red dotted line on the left is the
> > turbine
> > inlet temperature. One must stay between the red lines. The
> > black curves
> > can be considered as HP lines as this is a diesel. More fuel
> > more HP.
> >
> > Do we need a 3D?
> >
> > BTW Dave this R&D you are doing IMHO will become invaluable when
> > the time comes
> > to build a turbo compound rotary. I thank you in advance. The
> > world will
> > owe you a debt of gratitude.
> > --
> > Paul Lamar ...No rotor no motor
> >
> > .
> > Paul,
> > You snatched the words right out of my mouth and it's something I
> > suggested
> > some time ago. At the time you requested a drawing and II supplied a
> > rough
> > one, but to be fair all things must be tried and I would suggest
> > they have
> > been pretty well tried by Dave to this point.
> >
> > I wonder how Mistral are doing theirs. Regardless restricting the
> > heat and
> > flow is the most obvious way to assure survivability of the Turbo IMHO.
> > George (down under)
> >
> > I am rapidly coming to the conclusion that the problem lies with the
> > RPM and not the turbine temps. 1050 C is 1900 F.
> >
> > The turbine temps are about half the EGT temps.
> >
> >
> > Paul Lamar ...No rotor no motor.
> >
> >
> > Paul,
> > This may sound overly simplistic, but if too much heat is the culprit,
> > why not move the turbo further away from the exhaust ports? Seems to me
> > that this would dissipate a good portion of the excessive heat and also
> > the excess flow as the exhaust will contract as it cools. I vaguely
> > recall seeing a picture of someone's turbo installation where the turbo
> > is located downstream of a tangential muffler (possibly Tom Parkes'
> > 20B). Tom doesn't post often, but last I heard, he wasn't having any
> > turbo problems.
> >
> > Mark S.
> > 67.7 hrs (no turbo)
> >
> > I now don't think heat is the main problem given the recent Borg Warner
> > FEA's on the subject. The turbine is operating at half the EGT's temps.
> > See the attached charts of temperature.
> >
> > I think the reason Tom's is working better is its an aircraft turbo.
> > Obviously aircraft turbo's are designed differently and for a constant
> > speed engine
> > and moderate to high engine HP. That to me means a modest HP turbine
> with a
> > large compressor. There is so much kinetic energy in the rotary engine
> > exhaust it
> > is easy to over speed the car turbo charger. Brief over speeds don't
> > hurt it.
> > Long term over speeds will destroy it.
> >
> > The aircraft turbo has the effect of keeping the turbo charger RPM
> > within limits. Dave
> > had his car turbo charger modified along those lines. A larger
compressor
> > was added.
> >
> > "The compressor is a 60-1 and the turbine is a TO4 clipped to fit in
> > the stock housing. With the wastgate open [it] can only make about
> 30" MAP
> > at that altitude, but I can't use it all because my prop is not big
> > enough. I hit 6700 engine RPM but I didn't feel comfortable staying
> > there." [2.17:1 gear box].
> >
> > BNR Supercars
> > 393 Coupland Rd.
> > Branchville, AL 35120
> > (205) 640-1193
> >
BNRsupercars@yahoo.com <mailto:BNRsupercars@yahoo.com> / AIM:
> BNRsupercars
> >
> >
> > I think it was a large step in the right direction. With a spacer
> > between the stock 2nd gen turbo and stock manifold a yet larger
> compressor
> > could be added.
> >
> > Unfortunately what was also done, as I recall, was the exducer was
opened
> > out which was a small step in the wrong direction.
> >
> > "The turbine housing is opened up tremendously therefore decreasing
> > backpressure."
> >
> > You want to keep some back pressure on the turbine to keep the turbine
> > HP and RPM down.
> >
> > Most car turbocharger tuner guys don't understand the problems
> adapting car
> > turbo chargers to aircraft use.
> >
> > It is all in Hugh MacInnes book "Turbochargers" but you have to
> > read between the lines sometimes and think about the implications.
> >
> > Paul Lamar
> >
> > P,
> >
> > Please indulge a question here:
> >
> > Has anyone ever calculated the rpm at which an impeller fails...?
> > I'd think that it would be fairly easy to use engineering data to
> > calculate that value for several curves based on temperature.
> >
> > Let's say that, at ambient temperature (room temp), the impeller has
> > to reach 250,000 rpm (calculated) before failure. We all believe that
> > as temperature rises, the strain is increased and the impeller will
fail
> > sooner. Why not show a series of (calculated) curves, plotting stress
> > against strain (to failure) for a set of temperature curves near (900
> > deg to 1,400 deg) what we believe the operating temperature of the
> > turbocharger impeller....?
> >
> > Jack Beale
> >
> > Given the lack of information from turbo charger manufacturers on
> > HP of the turbines I don't think it is possible to calculate the RPM.
> > Perhaps I am wrong. One might figure the HP required to generate x
amount
> > of compression and then go into the compressor map to determine
> > the RPM.
> >
> > We still need a turbo tach. A turbo tach would also allow us
> > to determine the turbo charger RPM acceleration. We can then tell
> > where we are relative to compressor load.
> >
> > BTW I just learned something about that subject watching the Formula
> 1 races.
> > Ferrari listens to and watches the Speed Channel and determines the
> rate of
> > acceleration of their competitor's cars by analyzing the on board
> sound of
> > the engines :)
> >
> > Paul Lamar
>
> If the problem is that the temperatures of the exhaust are too high for
> the turbocharger blades to handle, can the wave rotor combustion turbine
> (see article below) help the situation?
>
>
http://www.avweb.com/eletter/archives/avflash/1147-full.html#198158
> New Turbine Cleaner, More Efficient
>
http://www.grc.nasa.gov/WWW/cdtb/projects/waverotor/index.html
>
http://www.grc.nasa.gov/WWW/cdtb/projects/waverotor/wavediv.html
>
http://www.grc.nasa.gov/WWW/cdtb/projects/waverotor/4port.html
>
> The gas turbine engine is due for an overhaul and Engineers at Purdue
> University have reached the testing stage of the wave rotor combustion
> turbine, a new generation of gas turbine engines. They say the engine is
> about 15-20% more efficient and could cut carbon dioxide emissions in
> aircraft by 20 percent or more over traditional gas turbine engines now
> in use. According to NASA, the wave rotor combustion turbine derives its
> efficiency from a rotating core that is exposed to hot and cold flow
> which keeps its mean temperature considerably lower than the peak cycle
> temperature. Leading the project is Razi Nalim, P.E., Ph.D., associate
> professor of Mechanical Engineering at Indiana University-Purdue
> University Indianapolis (IUPUI). ?Our goal is to design an alternative
> to the gas turbine application that is just as reliable, but cleaner,
> more efficient, and more powerful," said Nalim. "It will not only help
> reduce fossil fuel consumption and greenhouse gas emissions in
> traditional applications like airplanes and power generation, but a
> lighter, more efficient engine may allow Boeing to design an aerospace
> plane to carry us all the way to outer space and return safely to
> earth.? To further assist the development of this new technology, IUPUI
> has recieved a $200,000 award from the Rolls Royce Corporation to
> continue the design and testing process. Dr. Nalim and his team expect
> to be operational by the end of the year with a test rig to help prove
> the benefit of the concept. "Jet engine technology is pretty mature,"
> said Nalim. "To make a really big improvement you need to make a pretty
> significant change."
>
> Leslie Nordman
>
> Kind of off topic Les. Not something we can do to solve the
> immediate turbo charger problem.
>
> Paul Lamar
To all:
Sorry, Paul, and sorry to you, gentlemen, for taking the thread off
topic. Sending it off topic was not my intention: I was trying to think
out of the box for a better solution to Mr. Leonard's turbo charger problem.
I thought a combustion turbine, a structure that must deal with extreme
heat and pressure, could also deal with the extreme heat and pressure of
a turbocharger turbine. I thought that, if the kind of turbine and
temperatures were Mr. Leonard's problems, one stone (the new kind of
turbine the Purdue researchers are making) would kill both birds (the
temperature and turbine efficiency problems). Sending one stone after
two birds, however, has hurled FOD in the subject thread intake! :-)
Seriously, the wave rotor combustion turbine
_is_ experimental and will
take time to develop. It cannot solve the immediate problem.
My apologies,
Les Nordman
Naw! It is not all that bad Les :) Thanks for thinking about it.
BTW I don't understand that thing. It looks like a rotating combustion
chamber and not a turbine. One of the diagrams shows it installed
ahead of a turbine. Maybe it is a device to keep the kinetic energy up
while cooling off the gases. I did not spend a lot of time studying it.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.