Subject: 2 place BD 5 kit?
From: Rotary Engine
Date: 6/27/2008, 12:47 PM
To: AAA Put this in the To box


 Paul, A few wks ago someone asked about the rotary in a 2 place BD 5.
 Who is the kit manuf of the 2 place? Was it someone in UK? Can't seem
 to find that web site. Thanks, Dave D

 Here is the old message Dave.

 One of the principles is on the list.

 Sébastien <sebastien.lefebvre@lhaviation.com
<mailto:sebastien.lefebvre@lhaviation.com>>

 What kind of engine do you have in there Sébastien?

 Paul

 -----------------------------
 > Any rotary powered BD-5s under construction or flying?
 >
 > Jim Rudholm

 Here is a similar all composite BD5 (2 seats) made by the French. Would
 love
 to put a rotary engine in this one. But can not afford it. I think the
 asking price with engine is 100 000 Euros, not sure.

 Marc J.
 http://www.lhaviation.com/site_frame/bases_marges/index.htm

 http://fr.youtube.com/watch?v=UpmvstZuolA

 Hello !

 Directly copied from the site's english brochure :

 "Concerning the propulsion, LH Aviation proposes the Rotax 912 ULS. It
 develops 100hp
 and it is cooled by liquid and air. Other alternative engine is under
 consideration such as gas
 turbine, turboprop and engines between 80 hp to 165hp."

 Why not a rotary ?

 Nevertheless, changing the engine means adapting the propeller
 shaft, and
 one must be very
 cautious about vibrations and vibration induced problems ( the tail
 control
 surfaces are not very far !!!)

 Philippe Dejean

 The rotary vibrates less than a 912.

 --
 Paul Lamar ...No rotor no motor.

 Dear all,

 We choose the rotax 912s to put on our aircraft. The rotary engine
 is a good
 choice for a pusher aircraft like we have. You reduce the problems of
 vibration on the shaft. But I think, paul you can confirm, that you have
 more temperature on the exhaust so it's not always easy to cool.

 We are looking for rotary engine so we will see may be one day.

 Regards

 Sébastien Lefebvre

 Président/ CEO

 Aérodrome de Melun-Villaroche

 77550 Limoges- Fourches

 Tel: 01.64.87.19.07

 www.lhaviation.com <http://www.lhaviation.com/>

 Hang in there Sébastien. There are a couple of new
 single rotors in the works. If Mazda based it would be 120 HP at
 7500 RPM.
 Exhaust is no problem if you use Inconel. If you use 321 SS you must
 go up on the thickness to about .065" for close in work and thinner
 as you get further out. Also try to keep the mufflers hollow
 as anything inside is likely to be destroyed.
 --
 Paul Lamar ...No rotor no motor.

The problem for a two rotor driving a remote shaft is the same as
discovered by Jim Bede years ago. That is
torsional harmonics in the shafting system and the engine. At the time
it was a 2 cylinder 2 cycle engine with two power strokes per
revolution. Just like a rotary. Eventually overcome, but daunting at
first. Pulleys overheated. Brackets broke. Crankshafts broke, and so-on.
Super soft mountings became the rule. But that allows lots of movement.
The shaft acts like a bell, and happy at a number of frequencies. One of
the engineers wrote an explanation on it, but I cannot find it at the
moment.

Another fix is a big heavy flywheel, but that cure was never used.

Lynn E. Hanover

Lynn, and group,
Put BD-5 and torsional vibration in your search engine and you will find
this paper. It is a very interesting read. Too bad for Bede that dual
mass flywheels weren't available then.
Bill Jepson

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.