Suppose that we did have some well tested aluminum rotors, and they work
fine, and the groove don't wear out, and they don't get too big
when
hot
and
open the seal end gaps and so on. Or, we slot the corner seals,
and some how the
crush fit for the steel backed rotor bearing does not
vanish at operating temps, and we build an airplane engine with this
magic aluminum.
Suppose the new rotor weighs 1 pound instead of nearly 10 pounds.
Counter weights will be down to about a pound each. Good news.
Any additional HP will only come from processing more fuel, so if you
really need more than 230 or so then you need more RPM and then maybe a
3.5:1 reduction unit.
Muffling will be more involved or with ceramic coatings a turbo.
But you will be giving away more than one advantage of cast nodular
iron, and there are many.
The one I like is flywheel effect from 20 pounds of iron. The two torque
pulses per revolution with no flywheel effect may be more fun than you
can
imagine. Once at speed there may not be a big problem, but shame on
you at part throttle. And idle will be a school in tuning. Ignition only
after TDC. Lean, slow
burning mixture maybe only injecting alternate
revolutions, and so on.
So now its on the torque stand and has been running fine. The first
reduction box is back at Tracy's to get autopsied, and power is good
but
now the new box is showing slivers of steel in the filter, and we have
built a new heavy flywheel to take out those awful jerks and jumps under
1600 RPM. Strange, the flywheel weighs 20 pounds????????
If its for a race car, where recurring accelerations will yield improved
times to RPM, then a very light rotating assembly is important. The
weight differences may not show up on a dyno at all and lighter
assemblies may prove to be less effective when they allow
undamped
harmonics where heavier pieces had no such problems. In a steady state
power measurement the current engine might show up better than the new
lighter rotor engine.
So you buy a new race engine from the guy who beats the snot
out of you
every weekend, and your plan is that since you have identical cars and
about the same equipment, and of course you can drive better than that
old guy, you will teach him a lesson next week at Mid Ohio. Your home
track.
Ouch......He is still 2 seconds faster. Not as bad as 3 seconds but this
engine he sold you must be lame.
He says lets swap cars for the next session, you leap at the chance. His
car was a past National champion.
He is a second faster in your car than you are.. And he was only out for
two laps. You stay out for the whole session 9 laps and your best was a
second faster than your car. Damn...........
He says lets walk the track at noon, and in the mean time here is a list
I made up that might help you.
During the walk you find out your solid knowledge of Mid Ohio turns out
to be vestigial. He gifts you his copy of Driving in competition by Alan
Johnson. His list says
that the engine seems fine, the 4-5 spread is too
tall. The final drive ratio is too tall, 4th is faster than shifting to
5th then back. You need a carbon fiber drive shaft.
Loose the Centerline wheels and buy PPS wheels. Mount Good-Years forget
the Hoosiers. He says you have to wind it to 9,600 on each shift. The
rear bar on full soft is still way too stiff.
His crew chief, (another old guy) explains to your crew chief (also your
father in-law) that the recurring acceleration of that extra mass costs
time. The
Good-Years only last 2 weekends but weigh 10 pounds and stick
real good over 150 degrees.
The Hoosiers last 4 weekends but weigh 15 pounds and need 200 plus
degrees to stick at all. Not going to happen on the rear tires
In the race:
The old guy drives off his pace a bit, and gives you a driving clinic,
just driving his line, you turn in your very best lap time ever. On the
last lap, he
shifts at 9,600 instead of 9,300 RPM and yanks you 6 cars
down the long straight like he has 30 HP on you and wins again. You are
now friends with the old guys, who and all and all seems to know more than
you.
The
difference is the recurring acceleration of the rotating assembly where
one is a whole lot heavier than the other. If you think about it longer,
you see that braking is more effective as well.
(Wheels and tires are big
flywheels)
On an inertia dyno, that measures time to RPM, the heavy rotating
assembly will show up as less HP than a lighter rotating assembly. On
a water brake dyno it may not show up at all.
Lynn E. Hanover
That is very good Lynn. You have a real talent for writing.
Very interesting.
The aluminum rotor will never be one pound. Iron .3 pounds per cubic inch.
Aluminum .1 pounds per cubic inch.
Hi silicon content aluminum expands much less than regular
aluminum
and is closer to iron. That is why they make pistons out of it..
That is also why Mazda went to it for rotor housings.
Piston ring slot wear is more of an issue in pistons as the rings
move back and fourth unlike the apex seals in a rotary engine.
So far I have not found a conversion for expansion per degree Kelvin
to inches per inch per
degree F. Perhaps someone on here can help me out.
Don't forget the torque isolator. Tracy's is tunable
and working very well. No real need for a 20 pound flywheel.
And yes I think 150% more power will show up on a water brake dyno.
That is of course the dyno is capable of 16,000 RPM.. P-ports both of
course.
Furthermore :)
"In this study, an aluminum alloy, AA1050, was reinforced with an
interconnected, axisymmetrical, galvanized iron wire preform.
The composite was synthesized using disintegrated melt deposition
technique followed by hot
extrusion. Micro structural characterization
conducted on the composite samples showed good interfacial integrity
and low volume percent of non-interconnected porosity. Physical property
characterization showed that the coefficient of thermal expansion of the
composite decreased below the
values predicted by the theoretical models.
Hardness test conducted on the materials revealed that the composite
matrix exhibited a higher hardness when compared to the monolithic
aluminum alloy. Tensile property characterization revealed that, even
with a low volume percentage (0.896%) of the reinforcement, the elastic
modulus of the composite material increased beyond the value predicted
by the Rule-of-Mixture model. The 0.2% yield strength and the ultimate
tensile strength of the composite material and the monolithic aluminum
alloy remained within each other¢s standard deviation while the ductility
of the composite material
decreased."
Paul Lamar ...No rotor no motor.
http://www.unitconversion.org/unit_converter/thermal-expansion.html
http://www.engineeringtoolbox.com/linear-expansion-coefficients-d_95.html
About twice the
expansion rate of cast iron.
Rob Woods
Great conversion site Rob. Thanks for finding that.
According to this site. Si/Al Alloy is 000.000011 per degree F... inches
per inch while steel is given at 0.0000063 per degree F... inches per inch
I don't have it for iron.
Lets say the 3 inch wide Si/Al rotor gains 430 F from room temp when running
flat out. The Si/Al rotor gains 15 thousands in width while the steel rotor
gains 8 thousands in width. The Si/Al rotor then would then need to
be about 8 to 10 thousands of an inch narrower to fit the stock
rotor housing.
The current side seal slot depth in the cast iron rotor is
about 150 thousands (.15 inches). The side seal slot in the Si/Al rotor
could then be 8 thousands of an inch deeper and the side seals themselves
are about 150 thousands wide. The Si/Al seals would then be about 154
thousands.
Each side shares the travel so I don't
think that is necessary.
I'll leave the calculation of the increase in OD of the rotor to the reader
but
it is equally not much of a problem.
The rotor bearings could be pressed into a steel insert cast into the rotor.
I notice the Corvette engine runs the mains in the aluminum block
directly with steel main bearing caps. That has got to be a heat distortion
nightmare :) Lots of aircraft engines run the main bearing shells in the
aluminum
block directly. The bearing shells could be pressed into the Si/Al rotor after
it is heated to 500 F.
BTW an Al/Si rotor would pay off weight wise much better with a one rotor
engine.
--
Paul Lamar ...No rotor no motor.
I am way too lazy to check your math/data right now but it is important
to note that the K measurement uses meters and the F uses inches. That
is compensated for in the conversion but just keep that in mind when
making comparisons. I forgot to mention that in my previous email.
Rob Woods
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.