Subject: Saving fuel 555
From: Rotary Engine
Date: 7/10/2008, 5:28 PM
To: AAA Put this in the To box




      Paul,
      A better mass air sensor to use is the unit found in ford V8 trucks
      from 97 and up. Many of them in salvage yards. They were for
   engines of
      220 to 260 hp putting them in the flow range we need. Also very light
      and reliable. Just don't get one from the supercharged trucks, as
   they
      are 90mm diam. Larry

      Thanks for the tip Larry. Are they mechanical like the Mazda or
      electronic? The electronic are harder to use as they are tougher to
      interface with the 555. The Mazda unit is just a trap door
   connected to
      a pot.

      --
      Paul Lamar ...No rotor no motor.


      Paul,
      Pin out attached.
      Larry

      The problem is 5 volts is high airflow and the 555 fed 5 volts
   would be
      narrow pulse. Zero volts would be a wide pulse out of the 555.
   What you
      one must do is come up with a circuit that reverses that and probably
      increases it to 12 volts. Using the Mazda simple device you just wire
      the pot backwards.

      I am not saying it can't be done. Just more trouble.
      --
      Paul Lamar ...No rotor no motor.

      I would call such a circuit an op-amp.  Inversion and scaling in one
      step.

      Bob W.


      --
      N93BD - Rotary Powered BD-4 - http://www.bob-white.com
      3.8 Hours Total Time and holding
      Cables for your rotary installation - http://roblinstores.com/cables/


      Sounds like you are the man for the job Bob. Care to do a
   schematic and
      make a prototype on a plug board?

      Here is what the Mazda unit would look like along with the original
      Chaparral 2D  ram air box from 1965.

      --
      Paul Lamar ...No rotor no motor.

      OK, I'll draw up something 0-5V in, 12-0V out and build a breadboard
      circuit.  It may be a few days as I'm trying to finish up a couple of
      other projects.

      Bob W.

      --
      N93BD - Rotary Powered BD-4 - http://www.bob-white.com
      3.8 Hours Total Time and holding
      Cables for your rotary installation - http://roblinstores.com/cables/


      Great Bob.
      Thanks.

    ------------------------------------------------------------------------

      Here are the pin outs and resistance data on the Mazda mechanical
      air flow sensor if you want to keep it as simple as possible.
      The sensor air flow area is about 5 square inches so it is a bit of
      a restriction
      on a P-port engine with two... 1 7/8 ID runners have 5.52 square
   inches
      total  area. How much that is going to affect the power is hard
   to say.
      I intend to get the prop dyno working with the P-port RX8 engines
      so perhaps I will find out.

      The resistance varies between 50 and 500 ohms so the 555 pulse width
      with a 100 uF cap should be in the right range (1 ms to 50 ms) I am
      not sure this
      is going to work. It would be better if the pot was higher
   resistance.
      I'll have to mock it up on the bench.

    ----------------------------------------------------------------------------

      I am coming around to the hot wire and op amp approach.
      I suspect that a 100uF cap may not be practical for drift reasons
      and temperature
      change reasons.

      Here is a great little opamp calculator. http://www.bcae1.com/
      Scroll down to about the middle of the page.

      It will also work with a FreeScale MAP sensor if you don't want
   to use
      a mass airflow sensor.

      Here are hot wire sensor pictures from a Ford Escort.
      --------------------------------------------------------

      Bob, what do you think of this idea? Small daughter PC boards 50 mm
      (2") by 26 mm (1") with
      the op-amp, the 555 and the FET on them for each injectors. Modular.
      If one fails
      you carry a spare and plug it in.  Makes things easier to trouble
      shoot as well.

      The 50 by 170 mm (7") 3 rotor motherboard can have the pilot
      controls on it such as the start
      enrichment switch and the leaning pot. The whole works can be
      mounted behind the instrument
      panel. This should drastically reduced the wiring the installer
   must do.

      Also I am thinking that coax cable could be used for all other
      wiring. Coax is shielded
      and if it is Teflon it is hard to burn through in a fire. Nothing
      says you cannot
      use coax for DC. Also BNC connectors are cheap and they are shielded.

      It is about a buck a foot but cheap insurance against RF
   interference.
      Lots of people have had problems with that lately.



      Paul Lamar ...No rotor no motor.


   I don't think coax is necessary as I don't think any other part of the
   circuit is going to be a controlled impedance environment.  Coax is
   useful (required) where power transfer is critical from one device to
   another (antenna systems and other high frequency systems (MHz+).
   Tefzel (standard Aircraft Spruce) shielded wire should be perfectly
   suitable for the signaling in this kind of system.  The power and ground
   don't need shielding - but the wire needs to be plenty big, and there
   should be some filtering on these leads.  It might be a good idea to
   shield the signal (sensor) and injector wires.  Ground the shield only
   at the control box.


   Regards,

   Matt-

   All true Matt but I like the sledge hammer approach to RF interference.
   Do IT all in coax :) Using BNC connectors it is easy to disconnect
   things
   for trouble shooting and the grounding is built in. Cost is the only
   drawback but this is an airplane for heavens sake :)

   With the simple 555 system you have two wires coming from
   the two mag pick ups and four wires going to the injectors. Of
   course the top
   of the injectors are connected to 12 volts. The FET's merely ground
   the bottom
   side of the injector coils.

   BTW it is very very simple to mechanically change the injector
   timing by rotating the
   mag pick up steel plate relative to TDC.

   --
   Paul Lamar ...No rotor no motor.


I don't like fat coax because it's heavy and bulky...  I have seen
plenty of improperly installed BNC connectors.  DB (15,25) connectors
are easy to install and remove as well.  But, it's your airplane..  :)


Matt-

RG59/RG58  coax is only about .2 inch in diameter.
Probably a dozen people have had trouble trying to solder a zillion wires to DB connectors.
Yes I know you can get crimp on style but the wires are two small
for the current levels we are running. The shock and hold injectors require about
six amps. People building airplane are not necessarily electronic technicians.
We must keep it very robust and very very simple. You want DB buy Tracy.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.