Subject: Renesis porting and oil metering problems
From: Rotary Engine
Date: 7/14/2008, 7:15 AM
To: AAA Put this in the To box


Hello all,

I found this in my travels on the rx7club.com site. It has some
interesting takes on porting along with oil metering problems and
potential/actual fixes for the warranty issues that mazda has had with
rx-8 engines. Also this is not a prod at the p-port but I think that if
anyone is serious about using a rx-8 engine, such as myself in my
Starlet, it would be best served to read about this for potential mods
because until I see an actual dyno graph of a the p-port setup with
injection working correctly I will leave it under the "nice idea but
lets see some results" section which Paul has stated at some point he
was looking to rectify when he has the time/money. Its worth signing
into the rx7club.com site to read this because it has some interesting
points. That is if he is accurate as well. I am always a skeptic unless
i see concrete results in form of data. That is what I do as a vehicle
calibrator for Delphi. Enjoy. I keep finding these little nuggets of info:)

http://www.rx7club.com/showthread.php?t=766697

Paul,


The four NASA papers that I have are big (11 to 30M) and I dont know
where I got them from. I can email you the document numbers tonight when
I get home from work today or I can toss the actual papers at you. Do
you have an ftp site I can dump on?


Rob Woods

From: http://www.rx7club.com/showthread.php?t=766697

"Whatever you do, ALWAYS premix on a Renesis! I mean that for everyone
who owns a pre 09 model RX-8 too. Mazda messed up with the oil metering
system and it is why so many of those engines have been dying. They have
2 oil metering jets per rotor. Nothing out of the ordinary there. They are
both on the rotor housings now though instead of just 1 per rotor on the
housings. They are pointed towards the corners of the housings though as
they are trying to get oil to the corner seals now. This leaves the center
of the apex seal inadequately lubricated though. If you could see a chart
of seal temperatures you'd see that the center of the apex seal gets hottest.
That's where the oil metering is most important. This is the area of least
lubrication on the Renesis. Seals warp, compression goes down, wear increases.
This explains everything from inconsistent dyno numbers on RX-8's, low power
numbers, and even explains why Mazda has gone through so many ecu reflashes
on the car. They figured it out through and the 09 model cars now have a 3rd
oil injector per rotor! Mazda knows they messed up as they've extended the
engine warranty on all RX-8's to 100K miles. It's retroactive for those who
had already had their warranties expire. Mazda has not publicly admitted
that the oil metering was flawed in design. They are just fixing the issue
slowly and are trying to be quiet about it. Some of us figured it out though!
Use premix!" rotarygod

This is good advise about premix but I think this gentlemen is mis applying  information
on apex seal temperature he learned from the 13B data. One reason the 13B apex seal
runs hot is because of the peripheral exhaust port. The RX8 engine apex seal
may NOT run as hot.  I have seen no data so far on actual temperature measurements
on RX8 apex seals.

Mazda has a powerful incentive to cut down the amount of apex seal oil used to
reduce hc. BTW one of the main functions of the apex seal oil is to cool the
seal and not just to lubricate it. Mazda recently sent out a video and reiterated
the no synthetic oil policy due to lack of testing on their part. In the mean time
Castrol Syntec is one of the sponsors of the SpeedSource RX8. IMHO Mazda could
spend some time testing synthetic oils and recommending one of the them. I mean
...what is wrong about Idemitsu Rotary Engine oil? I personally and others have
used Mobile One for years with excellent results. Both in rotary cars and in
rotary powered airplanes. Mobile one break down temperature is at least twice
as high as regular motor oil. I am currently using Idemitsu in my RX8.

If you are bothered about it use silicon nitride seals from Francisco
or Sven :)

There are a lot of Mazda rotary engines in junk yards because Mazda uses cheap nylon lines
to carry oil to the apex seals. After about five or ten years these lines get brittle
and crack. So they must be frequently inspected and replaced. IMHO they should
have used steel lines for this critical function.

BTW we have had over 4,000 hits on our youtube video on how to p-port the RX8
engine. So far I have nothing from anybody on why it won't work :)

IMHO porting the RX8 rotary engine is not worth the cost. It is about the same cost
to p-port it and you get 25% more power at 7500 RPM. Mazda has every incentive
to cut down the cast iron wall thickness to cut the weight of the engine.
By now somebody somewhere has put one on a dyno besides my self :)

Rob, I don't know how to set up my site to ftp to.
If you send the titles I'll try to download them.
Some I may already have.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.