Subject: Renesis porting and oil metering problems
From: Rotary Engine
Date: 7/14/2008, 9:11 AM
To: AAA Put this in the To box



    Hello all,

    I found this in my travels on the rx7club.com site. It has some
    interesting takes on porting along with oil metering problems and
    potential/actual fixes for the warranty issues that mazda has had with
    rx-8 engines. Also this is not a prod at the p-port but I think that if
    anyone is serious about using a rx-8 engine, such as myself in my
    Starlet, it would be best served to read about this for potential mods
    because until I see an actual dyno graph of a the p-port setup with
    injection working correctly I will leave it under the "nice idea but
    lets see some results" section which Paul has stated at some point he
    was looking to rectify when he has the time/money. Its worth signing
    into the rx7club.com site to read this because it has some interesting
    points. That is if he is accurate as well. I am always a skeptic unless
    i see concrete results in form of data. That is what I do as a vehicle
    calibrator for Delphi. Enjoy. I keep finding these little nuggets of info:)

    http://www.rx7club.com/showthread.php?t=766697

    Paul,


    The four NASA papers that I have are big (11 to 30M) and I dont know
    where I got them from. I can email you the document numbers tonight when
    I get home from work today or I can toss the actual papers at you. Do
    you have an ftp site I can dump on?


    Rob Woods

    From: http://www.rx7club.com/showthread.php?t=766697

    "Whatever you do, ALWAYS premix on a Renesis! I mean that for everyone
    who owns a pre 09 model RX-8 too. Mazda messed up with the oil metering
    system and it is why so many of those engines have been dying. They have
    2 oil metering jets per rotor. Nothing out of the ordinary there. They are
    both on the rotor housings now though instead of just 1 per rotor on the
    housings. They are pointed towards the corners of the housings though as
    they are trying to get oil to the corner seals now. This leaves the center
    of the apex seal inadequately lubricated though. If you could see a chart
    of seal temperatures you'd see that the center of the apex seal gets
    hottest.
    That's where the oil metering is most important. This is the area of least
    lubrication on the Renesis. Seals warp, compression goes down, wear increases.
    This explains everything from inconsistent dyno numbers on RX-8's, low
    power
    numbers, and even explains why Mazda has gone through so many ecu reflashes
    on the car. They figured it out through and the 09 model cars now have a 3rd
    oil injector per rotor! Mazda knows they messed up as they've extended the
    engine warranty on all RX-8's to 100K miles. It's retroactive for those
    who
    had already had their warranties expire. Mazda has not publicly admitted
    that the oil metering was flawed in design. They are just fixing the issue
    slowly and are trying to be quiet about it. Some of us figured it out though!
    Use premix!" rotarygod

    This is good advise about premix but I think this gentlemen is mis applying
    information
    on apex seal temperature he learned from the 13B data. One reason the 13B apex
    seal
    runs hot is because of the peripheral exhaust port. The RX8 engine apex seal
    may NOT run as hot.  I have seen no data so far on actual temperature
    measurements
    on RX8 apex seals.

    Mazda has a powerful incentive to cut down the amount of apex seal oil used to
    reduce hc. BTW one of the main functions of the apex seal oil is to cool the
    seal and not just to lubricate it. Mazda recently sent out a video and
    reiterated
    the no synthetic oil policy due to lack of testing on their part. In the mean
    time
    Castrol Syntec is one of the sponsors of the SpeedSource RX8. IMHO Mazda could
    spend some time testing synthetic oils and recommending one of the them. I mean
    ....what is wrong about Idemitsu Rotary Engine oil? I personally and others have
    used Mobile One for years with excellent results. Both in rotary cars and in
    rotary powered airplanes. Mobile one break down temperature is at least twice
    as high as regular motor oil. I am currently using Idemitsu in my RX8.

    If you are bothered about it use silicon nitride seals from Francisco
    or Sven :)

    There are a lot of Mazda rotary engines in junk yards because Mazda uses cheap
    nylon lines
    to carry oil to the apex seals. After about five or ten years these lines get
    brittle
    and crack. So they must be frequently inspected and replaced. IMHO they should
    have used steel lines for this critical function.

    BTW we have had over 4,000 hits on our youtube video on how to p-port the RX8
    engine. So far I have nothing from anybody on why it won't work :)

    IMHO porting the RX8 rotary engine is not worth the cost. It is about the same
    cost
    to p-port it and you get 25% more power at 7500 RPM. Mazda has every incentive
    to cut down the cast iron wall thickness to cut the weight of the engine.
    By now somebody somewhere has put one on a dyno besides my self :)

    Rob, I don't know how to set up my site to ftp to.
    If you send the titles I'll try to download them.
    Some I may already have.
    --
    Paul Lamar ...No rotor no motor.



Paul,



Thats all I want to see is a dyno graph of an actual run with corrected
factors and such. I am not saying it wont work. What I am saying 4000
hits and no complaints in no way constitutes a claim of extra power.
Lets try to get some one to show some actual results here. There are
dumb asses that buy 10 dollar tornado air cleaners and claim 5 extra mpg
when it takes millions of dollars in work to get 1 or 2 mpg each year.
The proof is in the pudding. Also did you notice that he was saying 185
ft-lbs in another part of that post. I have emailed him asking for the
same as I asked from you.



Rob Woods



We got a dyno run at Mazdatrix using a Weber carb but Dave told me later
there was a problem with the dyno calibration.  There is no reason in my mind
why a p-port RX8 should be any different than a p-port 13B.
We have some dyno sheets on the 13B p-port with the same runner lengths,
diameters and port timing.

The Rx8 has a higher compression ratio and 17% more exhaust port
area.

The BSFC was all over the map indicating to me the the mixture was
all over the map. In an aircraft application you adjust the mixture
for the RPM and load.

I plan on taking the same engine and mounting it on my prop
dyno using the 555 EFI I am working on.


300 HP p-port 13B's have been around since the 80's.

Paul Lamar ...No rotor no motor.




The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.